Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

Selected vehicle: 2006 · GMC Yukon XL Denali

Change vehicle →

← Back to cases

Source reference 10168956

Manufacturer communication — 2006 GMC YUKON DENALI XL

Fitment confirmedReporter type: ManufacturerELECTRICAL SYSTEM

Relation to the target vehicle

  • The source's vehicle field includes the trim.
Model year
Match 2006 — Source vehicle field
Model
Match YUKON DENALI XL — Source vehicle field
Trim
Match Denali — Source vehicle field

What the manufacturer’s document says

PIT5074M ・ information ・ for GM vehicles in general

Applies to

  • Applies to all brands and models, 2005 - 2020.

    the passage
    All All 2005 - 2020 All All All All

Finding the cause

Possible causes

  • Terminal tension is one of the main culprits in an intermittent electrical concern, especially with very small terminals.

    the passage
    When diagnosing an intermittent electrical concern terminal tension is one of the main culprits, especially when working with very small terminals.

Steps to confirm (in the document’s order)

  1. Use test probe J-35616-64B to check tension on, or to probe, the .64 series terminals.

    the passage
    The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals.

  2. Use test probe EL-35616-58 to check terminal tension on the Mini .50 series terminals.

    the passage
    Also the EL-35616-58 is the latest test probe released for checking terminal tension on the Mini .50 series terminals.

Correction

Repair

  1. The terminal may also be used to make jumper wires, for example to jumper the High Speed LAN circuits together to bypass a module, for testing only.

    the passage
    This terminal may also be used to make jumper wires; example: to jumper the High Speed LAN circuits together in order to bypass a module for testing only.

  2. Crimp with tool J-38125-641, using jaw "H" for 22 ga wire, "J" for 20 ga wire, or "K" for 18 ga.

    the passage
    Use crimping tool J-38125-641 and jaw "H" for 22ga wire, "J" for 20 ga wire, or "K" for 18 ga.

  3. Replacement female terminals are available for harness side repairs.

    the passage
    Replacement female terminals are available for harness side repairs.

Parts

  • The test probe terminal is in terminal repair kit J-38125-620H, Lear Tray 7, part number 963716-2.

    the passage
    The test probe terminal has been released in the terminal repair kit (J-38125- 620H) located in Lear Tray 7 part number 963716-2 shown below.

  • The .64 test probe terminal already connected to a lead is GM part number 13505346, 5 terminated leads in a package.

    the passage
    Another option is to order the .64 test probe terminal already connected to a lead/wire called a terminated lead. The GM part number is 13505346, which can be ordered through your normal GM CCA parts channel. There are 5 terminated leads in a package, shown below.

Part numbers printed in the document

The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

Caution

  • Always refer to the Connector End View in Service Information to determine the correct test probe.

    the passage
    Note: Always refer to the Connector End View in Service Information for the latest information on determining the correct test probe to use.

  • Do not use the J-35616-64B if its terminal end is bent, damaged, worn or broken; obtain a replacement test probe or terminal.

    the passage
    If the terminal end of the J-35616-64B is bent, damaged, worn or broken, it should not be used and a replacement test probe or terminal should be obtained from GM Tools at 1-800- 468-6657 .

  • If the terminal end of the EL-35616-58 is bent, damaged, worn or broken, the probe must be replaced, because no male terminals are available at this time.

    the passage
    If the terminal end of the EL-35616-58 is bent, damaged, worn or broken, it will need to be replaced as there is no male terminals available at this time

Compiled by reading the full text of the document; each point stands on the passage shown. Check the document itself, linked below, before working on a vehicle.

Stated content

  1. Communication summary

    本予備情報通知は、J-35616-64B ターミナルテストプローブ、交換用ターミナル、および装着済みリード線の使用についてのテクニシャン向け情報を提供するものです。J-35616-64B は .64 シリーズターミナルの張力確認またはプロービング用に発行された最新のテストプローブです。テストプローブターミナルは、ターミナル修理キット(J-38125-620H)に収納されており、部品番号 963716-2 の Lear Tray 7 に配置されています。1パッケージ当たり 5 本の装着済みリード線があり、部品番号は 13505346 で、お客様の通常の General Motors カスタマーケア・アフターセールス部品チャネルを通じてご注文できます。 Machine translation (unreviewed)

    This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.Â
    Go to this passage in the original

Source

Source
NHTSA Manufacturer Communications
Source reference
10168956
Received by source
2019-12-09
Incident date
Unknown

Open original text and sourceOpen the provider's page (external)