Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Warning lightMisfire or rough idleLeakNoiseDoes not startHard start or long crankLoss of engine power, no accelerationCorrosion or rust

Record by record

96 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

How it is said to have ended

  • says it came back3
  • says it did not fix it1
  • result not stated6

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (17)

ENGINE AND ENGINE COOLING9

  1. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2024-02-29(2 earlier editions of this document folded here)

    Oil Cooler, Oil Cooler Lines, and Oil Tank Replacement Service Information

    1. 1Fault

      Not stated

    2. 2Finding the cause

      Possible causes

      • Debris from a damaged rod or main bearing is sent directly through the oil galleries and the components in the lubrication circuit.

    3. 3Correction

      Repair

      1. Whenever an engine assembly is replaced for a connecting rod or crankshaft main bearing failure, also replace the oil cooler, oil cooler lines, oil tank and turbocharger, if equipped.
      2. If the oil cooler is part of the radiator assembly, the radiator must be replaced along with the other required components.

      Caution

      • Reinstalling an oil cooler or cooler line from an engine with bearing failure debris may carry remaining debris into the new service engine.
      • Some service engines come with the oil cooler and/or oil cooler lines already attached; those need not be replaced.
      • Not every engine with bearing damage requires the oil cooler, lines or oil tank, or even the engine, to be replaced.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all GM passenger cars and trucks, 2000 through 2024, gasoline engines only.
    • Repair：Whenever an engine assembly is replaced for a connecting rod or crankshaft main bearing failure, also replace the oil cooler, oil cooler lines, oil tank and turbocharger, if equipped.
    • Repair：If the oil cooler is part of the radiator assembly, the radiator must be replaced along with the other required components.
    • Cause：Debris from a damaged rod or main bearing is sent directly through the oil galleries and the components in the lubrication circuit.
    • Caution：Reinstalling an oil cooler or cooler line from an engine with bearing failure debris may carry remaining debris into the new service engine.
    • Caution：Some service engines come with the oil cooler and/or oil cooler lines already attached; those need not be replaced.
    • Caution：Not every engine with bearing damage requires the oil cooler, lines or oil tank, or even the engine, to be replaced.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

  2. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2024-02-02(1 earlier editions of this document folded here)

    Piston Installation Procedure

    1. 1Fault

      Not stated

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      • Refer to the Engine Mechanical Specification in SI for the correct bore and piston specification.

    3. 3Correction

      Repair

      1. When installing a piston into a cylinder, use a ring compressor sleeve or equivalent for best results.
      2. Choose a sleeve with a smooth radius that tapers down to the specific bore size.
      3. Select a size only slightly bigger than the piston diameter and not larger than the cylinder bore diameter.

      Caution

      • If a sleeve is unavailable in the needed size, a universal ring compressor will work but is more difficult to use.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2024 and earlier GM passenger cars and trucks.
    • Repair：When installing a piston into a cylinder, use a ring compressor sleeve or equivalent for best results.
    • Repair：Choose a sleeve with a smooth radius that tapers down to the specific bore size.
    • Repair：Select a size only slightly bigger than the piston diameter and not larger than the cylinder bore diameter.
    • Confirm：Refer to the Engine Mechanical Specification in SI for the correct bore and piston specification.
    • Caution：If a sleeve is unavailable in the needed size, a universal ring compressor will work but is more difficult to use.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This PI bulletin advises the technician on the proper way to install the pistons in an engine.

  3. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2023-09-26

    Normal Transmission Shift and Throttle Response Delay

    1. 1Fault

      • A sag or hesitation may be noticed when coasting at low speeds of less than 24 km/h (15 mph) with a closed throttle and then aggressively applying the throttle.
      • With an automatic transmission, after a hard complete stop with a closed throttle immediately followed by an aggressive throttle opening, the downshifts may not be completed by the time the throttle is opened.
      • A sag or hesitation may also be noticed while cruising at highway speeds and then aggressively increasing the throttle, forcing a down-shift.

    2. 2Finding the cause

      Possible causes

      • In this maneuver the throttle blade is opened slowly for up to 0.7 seconds, even though the accelerator is applied aggressively, to help minimize driveline lash and clunking.
      • As a result, approximately 0.5 seconds of zero torque may be commanded to allow the shift to first gear to occur.

    3. 3Correction

      Caution

      • All of these conditions are a result of Torque Management and should be considered normal; no repairs should be attempted.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：GM passenger cars and trucks, model years 2000 to 2024.
    • Condition：A sag or hesitation may be noticed when coasting at low speeds of less than 24 km/h (15 mph) with a closed throttle and then aggressively applying the throttle.
    • Cause：In this maneuver the throttle blade is opened slowly for up to 0.7 seconds, even though the accelerator is applied aggressively, to help minimize driveline lash and clunking.
    • Condition：With an automatic transmission, after a hard complete stop with a closed throttle immediately followed by an aggressive throttle opening, the downshifts may not be completed by the time the throttle is opened.
    • Cause：As a result, approximately 0.5 seconds of zero torque may be commanded to allow the shift to first gear to occur.
    • Condition：A sag or hesitation may also be noticed while cruising at highway speeds and then aggressively increasing the throttle, forcing a down-shift.
    • Caution：All of these conditions are a result of Torque Management and should be considered normal; no repairs should be attempted.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

  4. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2023-09-15

    Engine Component Wear Service Guidelines

    1. 1Fault

      • Some technicians may be replacing engines instead of repairing them and replacing worn components as needed.

    2. 2Finding the cause

      Possible causes

      • The wear may be caused by the vehicle duty cycle, dust in the operating environment and local fuel quality.

      Steps to confirm (in the document’s order)

      1. Cylinder wall scratch: if a pick or fingernail cannot catch on it, the cylinder bore/engine block does not require replacement.
      2. With a scored piston, inspect for broken and/or stuck rings, and inspect the ring lands and cylinder wall for damage.
      3. When bearing failure is suspected, remove the oil filter and inspect it for excessive debris and damaged pleats.
      4. Minimal amounts of metal particles on the oil filter pleats should not pose a concern.
      5. Excessive metal particles or damaged filter pleats mean unfiltered oil with bearing debris may have been pumped into the oil galleries throughout the engine.

    3. 3Correction

      Repair

      1. Minor scratching/scoring on camshaft lobes and/or camshaft bearing journals: the scored components can be replaced without replacing the engine assembly.
      2. Minor scratching/scoring on connecting rod bearings: the scored components can be replaced without replacing the engine assembly.
      3. A slightly scored piston can be replaced without replacing the engine assembly.

      Caution

      • If inspection reveals cylinder wall damage (excessive scoring or out-of-round), an engine replacement may be required.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to GM passenger cars and trucks, model years 2000 to 2024.
    • Condition：Some technicians may be replacing engines instead of repairing them and replacing worn components as needed.
    • Cause：The wear may be caused by the vehicle duty cycle, dust in the operating environment and local fuel quality.
    • Repair：Minor scratching/scoring on camshaft lobes and/or camshaft bearing journals: the scored components can be replaced without replacing the engine assembly.
    • Repair：Minor scratching/scoring on connecting rod bearings: the scored components can be replaced without replacing the engine assembly.
    • Confirm：Cylinder wall scratch: if a pick or fingernail cannot catch on it, the cylinder bore/engine block does not require replacement.
    • Repair：A slightly scored piston can be replaced without replacing the engine assembly.
    • Confirm：With a scored piston, inspect for broken and/or stuck rings, and inspect the ring lands and cylinder wall for damage.
    • Caution：If inspection reveals cylinder wall damage (excessive scoring or out-of-round), an engine replacement may be required.
    • Confirm：When bearing failure is suspected, remove the oil filter and inspect it for excessive debris and damaged pleats.
    • Confirm：Minimal amounts of metal particles on the oil filter pleats should not pose a concern.
    • Confirm：Excessive metal particles or damaged filter pleats mean unfiltered oil with bearing debris may have been pumped into the oil galleries throughout the engine.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

  5. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2023-04-12(4 earlier editions of this document folded here)

    ACDelco Spin-On Oil Filter Torque Specification Notification

    1. 1Fault

      • An oil leak from underneath the front of the vehicle after an earlier oil service; the leak can take several thousand miles to appear.

    2. 2Finding the cause

      Possible causes

      • The oil may be leaking from between the oil filter gasket and the mounting surface.

      Steps to confirm (in the document’s order)

      • The filter may be very easy to remove, sometimes by hand.

    3. 3Correction

      Repair

      1. Lubricate the new oil filter gasket with clean engine oil.
      2. Install the oil filter 1 full turn after the gasket contacts the sealing surface on the filter mounting flange.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all passenger cars and trucks, model years 2000 to 2024.
    • Condition：An oil leak from underneath the front of the vehicle after an earlier oil service; the leak can take several thousand miles to appear.
    • Cause：The oil may be leaking from between the oil filter gasket and the mounting surface.
    • Confirm：The filter may be very easy to remove, sometimes by hand.
    • Repair：Lubricate the new oil filter gasket with clean engine oil.
    • Repair：Install the oil filter 1 full turn after the gasket contacts the sealing surface on the filter mounting flange.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.

  6. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2023-01-06

    EVAP Leak Diagnostic Service Bulletin (DTCs P0442/P0455)

    1. 1Fault

      • The MIL is illuminated, and DTC P0442 (EVAP small leak detected) and/or P0455 (EVAP large leak detected) may be set in the ECM.

    2. 2Finding the cause

      Possible causes

      • P0455 sets because of a large leak or a purge blockage: an unseated tube connection, a damaged tube, a canister vent valve stuck open, or a purge valve stuck closed.
      • P0442 sets because of a small leak, which can come from a purge valve stuck open or a canister vent valve stuck open.

      Steps to confirm (in the document’s order)

      1. Inspect every purge connection for proper installation, and look along the lines for damage or wear; if damage is seen, confirm it with the smoke test.
      2. Some leaks show only under pressure and some only under vacuum, so check both ways; cycling the purge and vent solenoids with GDS2 while inspecting may show a sticking valve.
      3. Critical connections to check include: purge tube to purge valve (at the intake manifold), purge tube to chassis EVAP line (rear of the engine, near the transmission), chassis EVAP line to canister, and fuel tank load line to canister.
      4. Also check the vent valve line at the vent valve, the fuel tank load line jumper connection near the fuel tank, and that the fuel tank cap is closed properly.
      5. If all connections are good, check the vent valve for a stuck-open position; if the vent valve works correctly, go on to the purge valve.
      1 more points

    3. 3Correction

      Parts

      • No parts are required for this repair.

      Caution

      • For diagnostic instructions, DTC information and required tools, always follow the service information document for the vehicle and DTC being worked on.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：This bulletin only applies to vehicles with gasoline engines.
    • Condition：The MIL is illuminated, and DTC P0442 (EVAP small leak detected) and/or P0455 (EVAP large leak detected) may be set in the ECM.
    • Cause：P0455 sets because of a large leak or a purge blockage: an unseated tube connection, a damaged tube, a canister vent valve stuck open, or a purge valve stuck closed.
    • Cause：P0442 sets because of a small leak, which can come from a purge valve stuck open or a canister vent valve stuck open.
    • Confirm：Inspect every purge connection for proper installation, and look along the lines for damage or wear; if damage is seen, confirm it with the smoke test.
    • Confirm：Some leaks show only under pressure and some only under vacuum, so check both ways; cycling the purge and vent solenoids with GDS2 while inspecting may show a sticking valve.
    • Confirm：Critical connections to check include: purge tube to purge valve (at the intake manifold), purge tube to chassis EVAP line (rear of the engine, near the transmission), chassis EVAP line to canister, and fuel tank load line to canister.
    • Confirm：Also check the vent valve line at the vent valve, the fuel tank load line jumper connection near the fuel tank, and that the fuel tank cap is closed properly.
    • Confirm：If all connections are good, check the vent valve for a stuck-open position; if the vent valve works correctly, go on to the purge valve.
    • Confirm：Work in this order: EVAP lines properly installed and fully seated; damage on the EVAP lines; vent valve malfunction; purge valve malfunction.
    • Parts：No parts are required for this repair.
    • Caution：For diagnostic instructions, DTC information and required tools, always follow the service information document for the vehicle and DTC being worked on.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

  7. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2022-09-07

    MIL Illuminated with Fuel Trim and Oxygen Sensor Codes

    1. 1Fault

      • Customers may comment that the MIL is illuminated.
      • Initial diagnosis may show fuel trim and O2 sensor related codes including P0101, P0137, P0138, P0140, P0141, P0157, P0158, P0160 and P0161.
      • The listed codes also include P0171, P0174, P0420, P0430, P1174 and P1175.

    2. 2Finding the cause

      Possible causes

      • These methods find small leaks around the O2 sensor embossments and slight cracks in an intake plenum or gasket.

      Steps to confirm (in the document’s order)

      1. If normal SI diagnostics do not lead to a resolution and an intake vacuum leak or exhaust leak is suspected, use the GE-52250 Variable Pressure Leak Detector (preferred), the J-41416 ultrasonic leak tester, or possibly soapy water with low pressure air into the tailpipe to find the leak.
      2. For an intake leak, introduce the smoke into the brake booster hose or the oil dipstick tube; soapy water can be sprayed near the gasket, seams and all vacuum nipples.
      3. For an exhaust leak, put the hose with smoke or air into the tailpipe sealed with shop towels, then spray soapy water around seals, seams and bosses.

    3. 3Correction

      Parts

      • No parts are required for this repair.

      Caution

      • All of these tests are much more effective if the throttle body is covered or sealed.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to Buick, Cadillac, Chevrolet and GMC passenger cars and trucks, model years 2000 to 2022, gasoline engines only.
    • Condition：Customers may comment that the MIL is illuminated.
    • Condition：Initial diagnosis may show fuel trim and O2 sensor related codes including P0101, P0137, P0138, P0140, P0141, P0157, P0158, P0160 and P0161.
    • Condition：The listed codes also include P0171, P0174, P0420, P0430, P1174 and P1175.
    • Confirm：If normal SI diagnostics do not lead to a resolution and an intake vacuum leak or exhaust leak is suspected, use the GE-52250 Variable Pressure Leak Detector (preferred), the J-41416 ultrasonic leak tester, or possibly soapy water with low pressure air into the tailpipe to find the leak.
    • Caution：All of these tests are much more effective if the throttle body is covered or sealed.
    • Confirm：For an intake leak, introduce the smoke into the brake booster hose or the oil dipstick tube; soapy water can be sprayed near the gasket, seams and all vacuum nipples.
    • Confirm：For an exhaust leak, put the hose with smoke or air into the tailpipe sealed with shop towels, then spray soapy water around seals, seams and bosses.
    • Cause：These methods find small leaks around the O2 sensor embossments and slight cracks in an intake plenum or gasket.
    • Parts：No parts are required for this repair.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

  8. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2021-04-19(4 earlier editions of this document folded here)

    Induction System Icing Inspection in Cold Ambient Temperatures

    1. 1Fault

      • The check engine light comes on and engine performance is poor in very cold ambient temperatures.

    2. 2Finding the cause

      Not stated

    3. 3Correction

      This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance. Â

    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Vehicles equipped with turbocharged gasoline engines, which may set DTC P0299 or P2227.
    • Condition：The check engine light comes on and engine performance is poor in very cold ambient temperatures.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance. Â

  9. Manufacturer communication2000–2002 GMC YUKON DENALI ・ 2018-06-04

    High Oil Pressure on Startup After Engine Replacement

    1. 1Fault

      Not stated

    2. 2Finding the cause

      Not stated

    3. 3Correction

      This preliminary informational bulletin provides information on High Oil Pressure on Startup After Engine Replacement Concern.

    Read the sentences of the record
    Remedy
    This preliminary informational bulletin provides information on High Oil Pressure on Startup After Engine Replacement Concern.

ENGINE6

  1. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2024-07-16(2 earlier editions of this document folded here)

    Fuel Injection Cleaner Kit Service Bulletin

    1. 1Fault

      • Rough idle, crank no start, extended crank or misfire, with the engine warning lamp on and DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 set.
      • When the engine is cold, compression on multiple cylinders may be zero.
      • The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.

    2. 2Finding the cause

      Possible causes

      • Major carbon build-up on the intake and/or exhaust valves from fuel contamination or incomplete burning of the fuel; misfires should not appear before at least 8,000 km (5,000 mi).

    3. 3Correction

      Repair

      1. If there is no valve damage and no cam follower out of place, perform the cleaning procedure to free sticking valves and remove carbon from the valves and pistons.
      2. If valves are damaged or cam followers are out of place, make the engine mechanical repairs first and then perform the cleaning procedure to prevent a return.
      3. Fill Cleaner Kit J-35800-A with about 650 ml (22 oz, 2 cans) of Air Intake, Combustion Chamber Cleaner and set the air pressure at the tool to 260 kPa (40 psi).
      4. With GDS 2 or a scan tool, command engine idle to 2000 rpm so the engine does not stall.
      5. With the engine at operating temperature in a well-ventilated area, slowly and carefully induce the cleaner into the engine, taking about 3 minutes.

      Parts

      • The Top Engine Cleaning Kit (ACDelco Air Intake, Valve and Combustion Chamber Cleaner and ACDelco Fuel System Cleaner 44K) is 19435372 for the U.S. and Canada.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Inducing too much cleaner at too low an RPM, or stalling the engine with too much cleaner at once, may hydro-lock the engine and bend a connecting rod.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to GM passenger cars and trucks with gasoline engines only, model years 2000 to 2025.
    • Condition：Rough idle, crank no start, extended crank or misfire, with the engine warning lamp on and DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 set.
    • Condition：When the engine is cold, compression on multiple cylinders may be zero.
    • Condition：The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.
    • Cause：Major carbon build-up on the intake and/or exhaust valves from fuel contamination or incomplete burning of the fuel; misfires should not appear before at least 8,000 km (5,000 mi).
    • Repair：If there is no valve damage and no cam follower out of place, perform the cleaning procedure to free sticking valves and remove carbon from the valves and pistons.
    • Repair：If valves are damaged or cam followers are out of place, make the engine mechanical repairs first and then perform the cleaning procedure to prevent a return.
    • Caution：Inducing too much cleaner at too low an RPM, or stalling the engine with too much cleaner at once, may hydro-lock the engine and bend a connecting rod.
    • Repair：Fill Cleaner Kit J-35800-A with about 650 ml (22 oz, 2 cans) of Air Intake, Combustion Chamber Cleaner and set the air pressure at the tool to 260 kPa (40 psi).
    • Repair：With GDS 2 or a scan tool, command engine idle to 2000 rpm so the engine does not stall.
    • Repair：With the engine at operating temperature in a well-ventilated area, slowly and carefully induce the cleaner into the engine, taking about 3 minutes.
    • Parts：The Top Engine Cleaning Kit (ACDelco Air Intake, Valve and Combustion Chamber Cleaner and ACDelco Fuel System Cleaner 44K) is 19435372 for the U.S. and Canada.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

  2. Manufacturer communication2000–2006 GMC YUKON ・ 2023-09-18(5 earlier editions of this document folded here)

    Misfire and DTC Codes Diagnostic Information

    1. 1Fault

      • With DTC P0300 - P0308 and/or P050D, use GDS and save the freeze frame records.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. Perform the relative compression test in the PICO NVH or Oscilloscope software; SI Document number 5518386 covers the procedure.
      2. If it passes the relative compression test, the concern is an ignition or fuel delivery issue.
      3. Check the ignition supply voltage to the ignition module/coil assemblies and also to the fuel injectors.
      4. Inspect the spark plugs for anything abnormal.
      5. Note the fuel trim values and on which bank, and compare actual MAF with calculated air flow.
      2 more points

    3. 3Correction

      Caution

      • The injector balance procedure in GDS is only a preliminary test and its results should not decide injector replacement, especially with a low or no flow injector.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：All brands and models with gas engines, model years 2000 - 2024.
    • Condition：With DTC P0300 - P0308 and/or P050D, use GDS and save the freeze frame records.
    • Confirm：Perform the relative compression test in the PICO NVH or Oscilloscope software; SI Document number 5518386 covers the procedure.
    • Confirm：If it passes the relative compression test, the concern is an ignition or fuel delivery issue.
    • Confirm：Check the ignition supply voltage to the ignition module/coil assemblies and also to the fuel injectors.
    • Confirm：Inspect the spark plugs for anything abnormal.
    • Caution：The injector balance procedure in GDS is only a preliminary test and its results should not decide injector replacement, especially with a low or no flow injector.
    • Confirm：Note the fuel trim values and on which bank, and compare actual MAF with calculated air flow.
    • Confirm：Check for a possible fuel quality issue, especially with a cold engine hard start and/or a misfire on all cylinders.
    • Confirm：Confirm whether a crankshaft variation learn has been completed and whether there is any abnormal engine noise possibly related to the misfire.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

  3. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2020-08-10(1 earlier editions of this document folded here)

    Needle Bearings in Roller Rockers During Oil Change

    1. 1Fault

      • Needle bearings may be found in the oil pan during an oil change.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. If roller rocker arm needle bearings are found during an oil change, inspect all the roller rocker arms.
      2. There should be 66 bearings, 33 a side.

    3. 3Correction

      Repair

      1. Replace only the broken roller rocker arm; the remaining roller rocker arms need not be replaced.
      2. Needle bearings may also be in the cylinder head oil drains; clean the oil drains to retrieve them.

      Caution

      • The oil pan does not need to be removed: the needle bearing is larger than the oil pump pickup screen mesh and cannot be pulled into the oil pump.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all brands and models, 2000 - 2021, with V6 or V8 push rod engines with roller rockers.
    • Condition：Needle bearings may be found in the oil pan during an oil change.
    • Confirm：If roller rocker arm needle bearings are found during an oil change, inspect all the roller rocker arms.
    • Repair：Replace only the broken roller rocker arm; the remaining roller rocker arms need not be replaced.
    • Repair：Needle bearings may also be in the cylinder head oil drains; clean the oil drains to retrieve them.
    • Confirm：There should be 66 bearings, 33 a side.
    • Caution：The oil pan does not need to be removed: the needle bearing is larger than the oil pump pickup screen mesh and cannot be pulled into the oil pump.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

  4. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2019-06-10

    Torque Converter Bolt Removal Warning

    1. 1Fault

      • Customers may comment on noise coming from underneath a vehicle equipped with an automatic transmission.
      • Technicians may find that the noise is coming from the bell housing area.

    2. 2Finding the cause

      Possible causes

      • Running the engine with those bolts removed may damage the pilot on the front of the torque converter, the pilot hole in the end of the crankshaft, or both.

      Steps to confirm (in the document’s order)

      • Use chassis ears to isolate the component or assembly that is the loudest source of the noise.

    3. 3Correction

      Caution

      • Do not remove the flex plate to torque converter bolts, push the converter back toward the transmission and start the engine to decide whether the noise comes from the engine or the transmission.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The model table lists all brands and models, model years 2000 - 2019.
    • Condition：Customers may comment on noise coming from underneath a vehicle equipped with an automatic transmission.
    • Condition：Technicians may find that the noise is coming from the bell housing area.
    • Caution：Do not remove the flex plate to torque converter bolts, push the converter back toward the transmission and start the engine to decide whether the noise comes from the engine or the transmission.
    • Cause：Running the engine with those bolts removed may damage the pilot on the front of the torque converter, the pilot hole in the end of the crankshaft, or both.
    • Confirm：Use chassis ears to isolate the component or assembly that is the loudest source of the noise.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

  5. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2018-09-17

    Engine Block Cylinder Bore Damage Preliminary Information

    1. 1Fault

      • The tip is for cases where cylinder bore damage, scoring or out of round is suspected as the cause of engine oil consumption, misfire, cylinder leakage or blow by.

    2. 2Finding the cause

      Possible causes

      • Dirt intrusion: if the air filtering system has been compromised the engine wears out very quickly; grit is found in the intake runners and the bores look lightly sand blasted.
      • Catalytic converter failure: if the converter brick is broken, its dust can be drawn back into the engine, and the bores look sand blasted.

      Steps to confirm (in the document’s order)

      1. The peak to valley specification for the crosshatch is .65-2.8 microns.
      2. Cylinder damage or scoring: the cylinder walls have grooves deep enough to catch with a fingernail.
      3. An out of round bore has areas where the crosshatch is missing or worn in different sections of the bore.
      4. If crosshatch is present all the way around the bore from top to bottom, the bore is not out of round.

    3. 3Correction

      Repair

      • With converter dust, the back cylinders go first if caught early; otherwise there is no crosshatch left and the engine needs to be replaced.

      Caution

      • GM has not had an issue with cylinders being machined out of round for any engine family in recent history.
      • A cylinder suspected of being oversize can only be confirmed by checking with an air gauge at the engine plant.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all brands, models and engines, 2000 - 2019.
    • Condition：The tip is for cases where cylinder bore damage, scoring or out of round is suspected as the cause of engine oil consumption, misfire, cylinder leakage or blow by.
    • Caution：GM has not had an issue with cylinders being machined out of round for any engine family in recent history.
    • Confirm：The peak to valley specification for the crosshatch is .65-2.8 microns.
    • Confirm：Cylinder damage or scoring: the cylinder walls have grooves deep enough to catch with a fingernail.
    • Confirm：An out of round bore has areas where the crosshatch is missing or worn in different sections of the bore.
    • Confirm：If crosshatch is present all the way around the bore from top to bottom, the bore is not out of round.
    • Cause：Dirt intrusion: if the air filtering system has been compromised the engine wears out very quickly; grit is found in the intake runners and the bores look lightly sand blasted.
    • Cause：Catalytic converter failure: if the converter brick is broken, its dust can be drawn back into the engine, and the bores look sand blasted.
    • Repair：With converter dust, the back cylinders go first if caught early; otherwise there is no crosshatch left and the engine needs to be replaced.
    • Caution：A cylinder suspected of being oversize can only be confirmed by checking with an air gauge at the engine plant.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

  6. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2018-06-11

    Metal Surface Cleaning Procedure

    1. 1Fault

      Not stated

    2. 2Finding the cause

      Possible causes

      • Abrasive pads produce fine grit that the oil filter cannot remove from the oil; this grit is abrasive and has been known to cause internal engine damage.
      • Abrasive pads can easily remove enough material to round cylinder head surfaces, which affects gasket sealing, especially in the narrow areas between combustion chambers and coolant jackets.
      • An abrasive pad removes 0.203 mm (0.008 in) of metal in about 15 seconds.
      • Aluminum Oxide in the engine oil causes premature engine bearing failure, in some cases in as little as 2,200 km (1,367 mi) or less after the repair.

    3. 3Correction

      Repair

      1. GM recommends a razor blade or plastic gasket scraper to clean the gasket surface on engine components that are to be reused.
      2. With a razor blade scraper, use a new blade for each cylinder head and corresponding block surface, and hold the blade as parallel to the gasket surface as possible.
      3. Alternatively, spray GM Low VOC Cleaner, P/N 19287401 (in Canada, P/N 88901247), on the mating surface.
      4. Let it soak for several minutes to loosen the old RTV sealer/gasket material, then remove the loose material with a plastic razor blade or non-metallic scraper.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Do not use abrasive pad/bristle devices to clean the gasket surfaces of engine components.
      • The appearance of the gasket surface is not critical, the feel is; indentations left by the old gasket in the cylinder head will be filled by the new gasket.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：2015 and prior GM passenger cars and trucks.
    • Caution：Do not use abrasive pad/bristle devices to clean the gasket surfaces of engine components.
    • Cause：Abrasive pads produce fine grit that the oil filter cannot remove from the oil; this grit is abrasive and has been known to cause internal engine damage.
    • Cause：Abrasive pads can easily remove enough material to round cylinder head surfaces, which affects gasket sealing, especially in the narrow areas between combustion chambers and coolant jackets.
    • Cause：An abrasive pad removes 0.203 mm (0.008 in) of metal in about 15 seconds.
    • Cause：Aluminum Oxide in the engine oil causes premature engine bearing failure, in some cases in as little as 2,200 km (1,367 mi) or less after the repair.
    • Repair：GM recommends a razor blade or plastic gasket scraper to clean the gasket surface on engine components that are to be reused.
    • Repair：With a razor blade scraper, use a new blade for each cylinder head and corresponding block surface, and hold the blade as parallel to the gasket surface as possible.
    • Repair：Alternatively, spray GM Low VOC Cleaner, P/N 19287401 (in Canada, P/N 88901247), on the mating surface.
    • Repair：Let it soak for several minutes to loosen the old RTV sealer/gasket material, then remove the loose material with a plastic razor blade or non-metallic scraper.
    • Caution：The appearance of the gasket surface is not critical, the feel is; indentations left by the old gasket in the cylinder head will be filled by the new gasket.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.

ELECTRICAL SYSTEM1

  1. Owner complaint2000 GMC YUKON DENALI ・ 2014-07-11

    Loss of power and hesitation on acceleration at highway speed

    1. 1Fault

    2. 2Finding the cause

      I HAVE LOOKED UP INFORMATION ON ISSUES THIS TRUCK HAS HAD AND 1 OF THEM IS REGISTERED UNDER NHTSA ID # 100032435 / PIP-4695.GM: LOSS OF POWER HESITATES ON ACCELERATION.

    3. 3Correction

    Read the sentences of the record
    Fault
    THE VEHICLE MAY OPERATE AS IF IT IS IN REDUCED POWER MODE.
    Cause
    I HAVE LOOKED UP INFORMATION ON ISSUES THIS TRUCK HAS HAD AND 1 OF THEM IS REGISTERED UNDER NHTSA ID # 100032435 / PIP-4695.GM: LOSS OF POWER HESITATES ON ACCELERATION.
    Remedy
    *PE I HAVE PURCHASED AN AIR MASS FLOW SENSOR, THROTTLE BODY SENSOR, ALL 4 O2 SENSORS, AND A COOLANT SENSOR.

VEHICLE SPEED CONTROL1

  1. Owner complaint2000 GMC YUKON ・ 2004-12-28

    Sudden unexpected acceleration while driving

    1. 1Fault

      WHILE DRIVING AT ANY SPEED THE VEHICLE SUDDENLY AND UNEXPECTEDLY ACCELERATED WITHOUT ANY WARNING.

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    WHILE DRIVING AT ANY SPEED THE VEHICLE SUDDENLY AND UNEXPECTEDLY ACCELERATED WITHOUT ANY WARNING.
    Remedy
    THE DEALER REPLACED THE ACCELERATOR AND THE CRUISE CABLES.
    Inspection
    THE DEALER INFORMED THE CONSUMER THAT THE THROTTLE BODY NEEDED TO BE REPLACED. *JB
    Outcome
    WITHIN 10 MONTHS AFTER THE REPAIR WAS MADE THE PROBLEM RECURRED WHILE DRIVING.

Showing 17 of the 96 you can open. Narrow the search to see the rest.