Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
1 conditions added

Common on this vehicle:LeakSmoke or fireWarning light

P0157 is written only in documents for GM vehicles in general. No record or document that names this vehicle states it, and it may not be a code this model year and engine set. The records are shown as their sources write them.

Record by record

2 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Read the records one by one (2)

ENGINE AND ENGINE COOLING2

  1. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2022-09-07

    MIL Illuminated with Fuel Trim and Oxygen Sensor Codes

    1. 1Fault

      • Customers may comment that the MIL is illuminated.
      • Initial diagnosis may show fuel trim and O2 sensor related codes including P0101, P0137, P0138, P0140, P0141, P0157, P0158, P0160 and P0161.
      • The listed codes also include P0171, P0174, P0420, P0430, P1174 and P1175.

    2. 2Finding the cause

      Possible causes

      • These methods find small leaks around the O2 sensor embossments and slight cracks in an intake plenum or gasket.

      Steps to confirm (in the document’s order)

      1. If normal SI diagnostics do not lead to a resolution and an intake vacuum leak or exhaust leak is suspected, use the GE-52250 Variable Pressure Leak Detector (preferred), the J-41416 ultrasonic leak tester, or possibly soapy water with low pressure air into the tailpipe to find the leak.
      2. For an intake leak, introduce the smoke into the brake booster hose or the oil dipstick tube; soapy water can be sprayed near the gasket, seams and all vacuum nipples.
      3. For an exhaust leak, put the hose with smoke or air into the tailpipe sealed with shop towels, then spray soapy water around seals, seams and bosses.

    3. 3Correction

      Parts

      • No parts are required for this repair.

      Caution

      • All of these tests are much more effective if the throttle body is covered or sealed.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to Buick, Cadillac, Chevrolet and GMC passenger cars and trucks, model years 2000 to 2022, gasoline engines only.
    • Condition：Customers may comment that the MIL is illuminated.
    • Condition：Initial diagnosis may show fuel trim and O2 sensor related codes including P0101, P0137, P0138, P0140, P0141, P0157, P0158, P0160 and P0161.
    • Condition：The listed codes also include P0171, P0174, P0420, P0430, P1174 and P1175.
    • Confirm：If normal SI diagnostics do not lead to a resolution and an intake vacuum leak or exhaust leak is suspected, use the GE-52250 Variable Pressure Leak Detector (preferred), the J-41416 ultrasonic leak tester, or possibly soapy water with low pressure air into the tailpipe to find the leak.
    • Caution：All of these tests are much more effective if the throttle body is covered or sealed.
    • Confirm：For an intake leak, introduce the smoke into the brake booster hose or the oil dipstick tube; soapy water can be sprayed near the gasket, seams and all vacuum nipples.
    • Confirm：For an exhaust leak, put the hose with smoke or air into the tailpipe sealed with shop towels, then spray soapy water around seals, seams and bosses.
    • Cause：These methods find small leaks around the O2 sensor embossments and slight cracks in an intake plenum or gasket.
    • Parts：No parts are required for this repair.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

  2. Manufacturer communication2000–2006 GMC YUKON DENALI ・ 2019-03-18

    Diagnostic Tip: Using Smoke Machine and Ultrasonic Detector for Air Leaks

    1. 1Fault

      • The SES light is on, and initial diagnosis may show fuel trim and/or O2 sensor related codes such as P0171, P0174, P0420 and P0430.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. If normal SI diagnostics do not resolve it and an intake vacuum leak or exhaust leak is suspected, the J41413-200 Evaporative System Tester smoke machine, the J-41416 ultrasonic leak tester, or soapy water with low pressure air into the tailpipe may help find the leak.
      2. For an intake leak, the smoke can be introduced into the brake booster hose or the oil dipstick tube.
      3. Soapy water can be sprayed near the gasket and seams and on all vacuum nipples.
      4. For an exhaust leak, a hose into the tailpipe carrying smoke or air, sealed with shop towels, is effective.
      5. Then spray soapy water around the seals, seams and bosses.
      1 more points

    3. 3Correction

      Caution

      • All of these tests are much more effective if the throttle body is covered/sealed.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all 2000 - 2019 models with gasoline engines.
    • Condition：The SES light is on, and initial diagnosis may show fuel trim and/or O2 sensor related codes such as P0171, P0174, P0420 and P0430.
    • Confirm：If normal SI diagnostics do not resolve it and an intake vacuum leak or exhaust leak is suspected, the J41413-200 Evaporative System Tester smoke machine, the J-41416 ultrasonic leak tester, or soapy water with low pressure air into the tailpipe may help find the leak.
    • Caution：All of these tests are much more effective if the throttle body is covered/sealed.
    • Confirm：For an intake leak, the smoke can be introduced into the brake booster hose or the oil dipstick tube.
    • Confirm：Soapy water can be sprayed near the gasket and seams and on all vacuum nipples.
    • Confirm：For an exhaust leak, a hose into the tailpipe carrying smoke or air, sealed with shop towels, is effective.
    • Confirm：Then spray soapy water around the seals, seams and bosses.
    • Confirm：These methods are very good for finding small leaks around the O2 sensor bosses and slight cracks in an intake plenum or gasket.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.