Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Warning lightReduced brakingNoiseABS activates (at low speed and the like)Corrosion or rustSeat beltSmoke or fireAir bag did not deploy

Possible causes

Vibration or shudder, ABS light0 records
Body, doors and interior
Brakes
Engine
Other
Suspension, wheels and tires
0RPO DL3 power folding mirror loose, moves or shakes after being folded by hand (cycle it electrically)0ABS lamp with DTC C0265 (EBCM motor relay circuit) after EBCM replacement0ABS light with C0265/C0201/U1041 or no communication with brake module (EBCM ground G110)0Violent steering wheel shake or vibration at road speed (brake booster)0Engine vibration or noise at idle felt in the steering wheel or seat (reprogram the PCM)0Tire recall (not the vehicle as built): Firestone Wilderness LE tread separation - recall 01T-0011500 only0Aftermarket part (not the vehicle as built): Federal-Mogul National / Carquest replacement wheel hub assembly retention nut - recall 07E-1062WD only
Causes with no correction stated (1)

Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.

Electrical, wiring and power
Intermittent no start with Service Stability, ABS light, 'Unknown Driver' and multiple DTCs / no module communication (0)

The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.

FaultCrate・GMC Yukon 2000–2006・Vibration or shudder, ABS light

Candidate cause (the documents say what to do)

RPO DL3 power folding mirror loose, moves or shakes after being folded by hand (cycle it electrically)

The result is that the mirror may move and/or shake.

These mirrors must always be moved electrically; a mirror folded inward by hand and moved back outboard by hand will not latch into the detent.

What to do

  1. If the mirror shows these conditions, cycle it inboard and back outboard with the electric controls; this makes the mirrors click into the proper detents.
  2. The "Do This" column says to cycle the mirror.

Caution: The mirrors fold inboard electrically with the same switches used for adjusting the individual mirrors: place the L/R toggle switch in neutral, then use the pad to fold the mirrors in or out.

What is needed

Parts and materials
Not stated
Labor time
Not stated
Special tools
Not stated
Scan tool
Not stated

Only what the technical documents state. "Not stated" does not mean not needed.

In the records

No record states work done for this cause.

See the evidence (1 technical documents, 0 records)

Passages of the technical documents

  • Concerns the operation of RPO DL3 mirrors on 2003 full size pickups and utilities.

    There are some misunderstandings about the operation of RPO DL3 mirrors on 2003 full size pickups and utilities (fig 12) .

    General Motors 2003-07-01

  • Row for 2003 C/K Fullsize Pickups & Utilities: mirror loose.

    2003 C/K Fullsize Pickups & Utilities -- Mirror Loose

    General Motors 2003-06-01

  • The result is that the mirror may move and/or shake.

    The result is that the mirror may move and/or shake.

    General Motors 2003-07-01

  • These mirrors must always be moved electrically; a mirror folded inward by hand and moved back outboard by hand will not latch into the detent.

    These mirrors must always be moved electrically. If a mirror is folded inward manually, and then moved back outboard manually, the mirror will not latch into the detent.

    General Motors 2003-07-01

Read every statement and its source →

Records

None among the records that can be opened now.

See all 0 records of this cause →

A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.

Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.