Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:Warning lightNoiseCorrosion or rustMisfire or rough idleLoss of engine power, no accelerationStalls or shuts off

Possible causes

ABS light, 20026 records
Brakes
Suspension, wheels and tires
3Unwanted ABS activation at low speed (front wheel speed sensor mounting corrosion)1ABS light with C0265/C0201/U1041 or no communication with brake module (EBCM ground G110)0ABS lamp with DTC C0265 (EBCM motor relay circuit) after EBCM replacement1Aftermarket part (not the vehicle as built): Federal-Mogul National / Carquest replacement wheel hub assembly retention nut - recall 07E-1062WD only

The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.

FaultCrate・GMC Yukon 2000–2006・ABS light, 2002

Candidate cause (the documents say what to do)

Unwanted ABS activation at low speed (front wheel speed sensor mounting corrosion)

These vehicles may have a condition permitting corrosion to occur between the front hub/bearing assembly and the wheel speed sensor.

With the brakes applied between about 6 km/h (3.7 mph) and 16 km/h (10 mph), the corrosion may cause unwanted ABS activation.

What to do

  1. The reading should be at least 350 mV AC; if it is less, the wheel speed sensor must be replaced.
  2. If the sensor's mounting surface is warped or bent, the sensor must be replaced.
  3. Dealers remove the sensor, clean its mounting surface on the bearing, apply rust inhibitor and grease, reinstall it and check peak-to-peak output voltage.
  4. The passage heading states that the repair is cleaning the wheel speed sensor mounting surface.
  5. The recall procedure is to remove the sensor, clean the mounting surface, apply a rust inhibitor (Zinc-X) to the surface and reinstall the sensor; the sensor is replaced if necessary.
  6. GM's earlier recall procedure in Canada also included greasing the mounting surfaces and verifying that the wheel speed signal output voltages were within specification.

Caution: Do not pry the sensor out of the bore; prying breaks the sensor body off in the bore.

What is needed

Parts and materials
  • Wheel speed sensor (when the reading is less than 350 mV AC)
  • Wheel speed sensor (when its mounting surface is warped or bent)
  • Rust inhibitor (Zinc-X, applied to the mounting surface)
  • Grease (applied to the mounting surface)
Labor time
Not stated
Special tools
Not stated
Scan tool
Not stated

Only what the technical documents state. "Not stated" does not mean not needed.

In the records

  • Wheel Speed Sensor: cleaned 1
See the evidence (2 technical documents, 3 records)

Passages of the technical documents

  • The recall covers 1999-2002 Chevrolet Silverado, 2000-2002 Chevrolet Tahoe and Suburban, 2002 Chevrolet Avalanche, 1999-2002 GMC Sierra, and 2000-2002 GMC Yukon and Yukon XL located in the listed severe-corrosion areas.

    MODELS: 1999-2002 CHEVROLET SILVERADO 2000-2002 CHEVROLET TAHOE, SUBURBAN 2002 CHEVROLET AVALANCHE 1999-2002 GMC SIERRA 2000-2002 GMC YUKON, YUKON XL LOCATED IN THE SEVERE CORROSION AREAS LISTED BELOW

    General Motors (recall bulletin filed with NHTSA under 05V-379) 2008-03-01

  • The condition is more likely in environmentally corrosive areas.

    THIS CONDITION IS MORE LIKELY TO OCCUR IN ENVIRONMENTALLY CORROSIVE AREAS.

    NHTSA (recall summary text as published by NHTSA)

  • The recall was launched only in the listed salt-belt states and the District of Columbia.

    THIS RECALL WILL BE LAUNCHED IN THE "SALT BELT" STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MARYLAND, MASSACHUSETTS, MAINE, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN AND THE DISTRICT OF COLUMBIA ONLY.

    NHTSA (recall summary text as published by NHTSA)

  • These vehicles may have a condition permitting corrosion to occur between the front hub/bearing assembly and the wheel speed sensor.

    These vehicles may have a condition permitting corrosion to occur between the front hub/bearing assembly and the wheel speed sensor.

    General Motors (recall bulletin filed with NHTSA under 05V-379) 2008-03-01

Read every statement and its source →

Manufacturer’s documents

A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.

Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.