Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Warning lightNoiseLoss of engine power, no accelerationCorrosion or rustGauge or instrument faultAir conditioning or heaterLights (headlights, turn signals)Does not start

Record by record

4 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

How it is said to have ended

  • result not stated2

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (4)

Known issuesService Stability message with DTC C0131, C0196, C0290 and/or C02921

  1. Manufacturer communication2004–2006 GMC YUKON ・ 2005-05-13

    Service Stability Message, DTC C0131, C0196, C0290 and/or C0292

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      SERVICE STABILITY MESSAGE ON, DIAGNOSTIC TROUBLE CODE (DTC) C0131, C0196, C0290 AND/OR C0292 SET. *TT

    Read the sentences of the record
    Remedy
    SERVICE STABILITY MESSAGE ON, DIAGNOSTIC TROUBLE CODE (DTC) C0131, C0196, C0290 AND/OR C0292 SET. *TT

Known issuesStability System Disabled / Service Stability message with DTC C0455 (bent terminals at the steering wheel position sensor)1

  1. Manufacturer communication2005 GMC FULL SIZE UTILITIES (YUKON) ・ 2005-07-01

    Stability System Disabled / Service Stability message with DTC C0455: bent terminals at the steering wheel position sensor

    1. 1Fault

      • Owners may comment on a Stability System Disabled or Service Stability message with DTC C0455.

    2. 2Finding the cause

      Possible causes

      • The concern may be caused by bent terminals on the SWPS (Steering Wheel Position Sensor).

      Steps to confirm (in the document’s order)

      • Remove the SWPS connector and inspect for bent terminals.

    3. 3Correction

      Repair

      • In most cases the terminals can be straightened without replacing the sensor.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2005 Cadillac, Chevrolet and GMC Full Size Utilities with RPO JL4.
    • Condition：Owners may comment on a Stability System Disabled or Service Stability message with DTC C0455.
    • Cause：The concern may be caused by bent terminals on the SWPS (Steering Wheel Position Sensor).
    • Confirm：Remove the SWPS connector and inspect for bent terminals.
    • Repair：In most cases the terminals can be straightened without replacing the sensor.

    Open this issue of GM TechLink ↗ The points above are read from an article of TechLink, GM’s monthly publication for dealership technicians. The article itself is not reproduced here.

    Remedy
    Stability System This information applies to 2005 Cadillac, Chevrolet, and GMC Full Size Utilities with RPO JL4. Owners may comment on a Stability System Disabled or Service Stability message with DTC C0455. This concern may be caused by bent terminals on the SWPS (Steering Wheel Position Sensor). Remove the SWPS connector and inspect for bent terminals. In most cases, the terminals can be straightened without having to replace the sensor.

ELECTRONIC STABILITY CONTROL (ESC)1

  1. Owner complaint2006 GMC YUKON ・ 2016-09-07

    Vehicle bogs down intermittently when starting or turning a corner

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    WHEN I AM STARTING OUT OR TURNING A CORNER THE VEHICLE WILL INTERMITTENTLY BOG DOWN. (1 more)
    Cause
    THIS HAS SOMETHING TO DO WITH THE STABILITRAK SYSTEM.
    Remedy
    I JUST DISCONNECT IT AT THE DASH AND PUT UP WITH THE YELLOW WARNING LIGHT.

SERVICE BRAKES, HYDRAULIC1

  1. Owner complaint2004 GMC YUKON DENALI ・ 2008-11-12

    Traction control message after stop, vehicle sluggish to accelerate

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    2004 GMC YUKON DENALI - TRACTION CONTROL MESSAGE COMES ON AFTER A STOP WHEN YOU START TO GO AGAIN AND IT FEELS LIKE THE VEHICLE DOES NOT WANT TO GO.
    Inspection
    WE HAVE TAKEN IT IN SEVERAL TIMES FOR THIS ISSUE BUT COULD NOT FIGURE OUT WHAT IT WAS DUE TO NO CODE IN THE COMPUTER.