GMC Yukon 2000–2006
Common on this vehicle:Gauge or instrument faultNoiseWarning lightCorrosion or rustLeakReduced brakingAir conditioning or heaterVibration or shudder
Possible causes
23 causes not drawn
- Crankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-5210
- Throttle body carbon build-up: idle surge, reduced engine power, throttle DTCs (high mileage)0
- Front right-hand brake pipe contact with body cross sill - recall 00V-3450
- Stability System Disabled message and unwanted StabiliTrak activation (tire wear or mismatched tires)0
- ABS lamp with DTC C0265 (EBCM motor relay circuit) after EBCM replacement0
- Intermittent MIL, service lamps/messages or DTCs from connector fretting corrosion1
- Reduced Engine Power from throttle body connector crimp, broken wire or grounds1
- Battery1
- Rear Window Defroster Contact1
- Rear door window inoperative (motor replacement)1
- Power Window1
- Sunroof1
- Service 4WD indicator and DTC B2725 (transfer case shift control switch)1
- 4WD/AWD lamps and system inoperative: "sleepy" New Venture Gear transfer case control module (reprogram the TCCM)1
- Transfer Case Speed Sensor Wiring Harness1
- No response when the OnStar button is pressed (DTC B2476): button assembly test values1
- Red OnStar LED and DTC B2455 after Canada upgrade bulletin 15-08-44-001 (audio and microphone drain wires shorted)1
- Telematics Control Module1
- Rear HVAC ticking noise, no rear temperature or mode control, DTC B0434 / B3764 (revised auxiliary HVAC control module)1
- Seat Heater1
- Instrument panel cluster gauges stick, flutter or stop working1
- CHECK OIL LEVEL message stays on after an oil change or top-off until the engine cools0
- Quadrasteer: rear wheels stay turned after the front wheels are straight (controlled re-centering after a fault, normal operation)1
The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.
FaultCrate・GMC Yukon 2000–2006・Warning light
Candidate cause (the documents say what to do)
Transfer case service light, New Venture Gear transfer case (replace the encoder motor sensor and reprogram the TCCM)
0 of the records matching this search name this component as the cause.
How to tell
C0327P0500P0836Service 4WD
What to do
- Verify that the encoder motor is the primary cause.
- Replace the encoder motor sensor and reprogram the TCCM; the labor operation is K9980.
Caution: Do not replace the module, the encoder motor or the transfer case for DTCs C0327, P0836, P0500; the reference is bulletin 03-04-21-001D.
In the records
No record states work done for this cause.
See the evidence (1 technical documents, 0 records)
Passages of the technical documents
2003 Fullsize Pickups and Utilities – Transfer Case Service Light/New Venture Gear Transfer Case
General Motors 2004-04-01
Verify that the encoder motor is the primary cause.
General Motors 2004-04-01
Replace encoder motor sensor and reprogram TCCM. Labor Operation: K9980
General Motors 2004-04-01
Don’t replace the module, encoder motor or transfer case for DTCs C0327, P0836, P0500 03-04-21-001D
General Motors 2004-04-01
A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.
Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.