Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
Add conditions (optional: symptom, model year, system, warning display, trouble code, kind of record)

Common on this vehicle:Gauge or instrument fault

remedyBody Control ModuleRemove

Record by record

2 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Read the records one by one (2)

ELECTRICAL SYSTEM2

  1. Manufacturer communication2003–2006 GMC YUKON ・ 2021-04-20

    IPC Odometer Programming Method Quick Reference Guide

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Remedy
    IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® – The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.

  2. Manufacturer communication2005–2006 GMC YUKON DENALI ・ 2017-08-15

    Automatic Door Locking Override Feature Service Communication

    1. 1Fault

      • Customers may say they cannot override automatic door locking; the "Doors Lock Manually" selection in the DIC was removed starting in the 2005 model year.

    2. 2Finding the cause

      Possible causes

      • Since the 2005 model year every BCM is factory programmed to lock all doors when the transmission is shifted into gear or vehicle speed exceeds 8 mph (13 km/h).

    3. 3Correction

      Repair

      1. Reprogram the BCM from Tis2Web: at the "Calibration Selection" screen select "locking" and pick the calibration "(Per customer request only) Auto Door Lock option ENABLED on DIC".
      2. After reprogramming, vehicles with Steering Wheel Controls (RPO UK3) get a new "Manual" selection in the "Auto Door Lock" personalization setting, next to "In Gear" and "With Speed".
      3. Vehicles without Steering Wheel Controls must enter the door lock programming mode described in section 2 of the owner's manual after the BCM is reprogrammed.
      4. In programming mode, one chime means Setting 1 (lock in gear), two chimes Setting 2 (lock with speed) and no chime Setting 3 (Manual).

      Caution

      • No new calibrations are available for the 2005 models or for vehicles with manual transmissions.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The second procedure applies to the 2006 GMC Yukon, Yukon Denali, Yukon XL and Yukon Denali XL.
    • Condition：Customers may say they cannot override automatic door locking; the "Doors Lock Manually" selection in the DIC was removed starting in the 2005 model year.
    • Cause：Since the 2005 model year every BCM is factory programmed to lock all doors when the transmission is shifted into gear or vehicle speed exceeds 8 mph (13 km/h).
    • Caution：No new calibrations are available for the 2005 models or for vehicles with manual transmissions.
    • Repair：Reprogram the BCM from Tis2Web: at the "Calibration Selection" screen select "locking" and pick the calibration "(Per customer request only) Auto Door Lock option ENABLED on DIC".
    • Repair：After reprogramming, vehicles with Steering Wheel Controls (RPO UK3) get a new "Manual" selection in the "Auto Door Lock" personalization setting, next to "In Gear" and "With Speed".
    • Repair：Vehicles without Steering Wheel Controls must enter the door lock programming mode described in section 2 of the owner's manual after the BCM is reprogrammed.
    • Repair：In programming mode, one chime means Setting 1 (lock in gear), two chimes Setting 2 (lock with speed) and no chime Setting 3 (Manual).

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about customers that are unable to override the automatic door locking feature. Technician will update the Body Control Module on 2006 to 2007 model years. On 2010 to 2014 model years technician will need to contact Techline Customer Support for calibrations.