Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
1 conditions added

Common on this vehicle:Gauge or instrument faultNoiseWarning lightCorrosion or rustLeakReduced brakingAir conditioning or heaterVibration or shudder

Record by record

19 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

How it is said to have ended

  • says it was fixed2
  • says it held for a while1
  • says it did not fix it2
  • result not stated7

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (19)

Known issuesUnwanted ABS activation at low speed (front wheel speed sensor mounting corrosion)11

  1. Owner complaint2002 GMC YUKON ・ 2016-03-01

    ABS engaged without warning and brake pedal stiffness while driving

    1. 1Fault

    2. 2Finding the cause

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT DIAGNOSED NOR REPAIRED.

      What the documents say to do

      Unwanted ABS activation at low speed (front wheel speed sensor mounting corrosion)

      Confirm

      • The reading should be at least 350 mV AC; if it is less, the wheel speed sensor must be replaced.

      Repair

      1. Dealers remove the sensor, clean its mounting surface on the bearing, apply rust inhibitor and grease, reinstall it and check peak-to-peak output voltage.
      2. The passage heading states that the repair is cleaning the wheel speed sensor mounting surface.

      Caution

      • Do not pry the sensor out of the bore; prying breaks the sensor body off in the bore.
    Read the sentences of the record
    Fault
    WHILE DRIVING 5 MPH (= 8.05 km/h), THE ABS ENGAGED WITHOUT WARNING WHEN THE BRAKE PEDAL WAS DEPRESSED. (2 more)
    Cause
    THE HYDRAULIC PUMP MALFUNCTIONED AND CAUSED THE CONTACT TO HAVE A DIFFICULT TIME PARALLEL PARKING WITHOUT THE VEHICLE ROLLING AWAY.
    Remedy
    THE VEHICLE WAS NOT DIAGNOSED NOR REPAIRED.

  2. Owner complaint2002 GMC YUKON ・ 2010-10-18

    ABS activating at slow speeds and recurring despite multiple repairs

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    THE PROBLEM OCCURS AT SLOW SPEEDS, SUCH AS COMING TO A STOP OR IN HEAVY COMMUTER TRAFFIC. (1 more)
    Remedy
    I BELIEVE THE SPEED SENSOR WAS ADJUSTED THE OTHER TIMES THE ABS WAS FAULTY, BUT THE DETAILS ARE DIFFICULT TO DETERMINE.
    Consequence
    THE FAILURE TO STOP HAS RESULTED IN TWO SMALL COLLISIONS BUT NO DAMAGE WAS DONE TO MY VEHICLE OR THE OTHERS.

  3. Owner complaint2002 GMC YUKON ・ 2010-03-23

    ABS activation during slow stops, increased stopping distance

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    ABS ACTIVATES DURING SLOW STOPS, INCREASES STOPPING DISTANCE.
    Cause
    I BELIEVE PROBLEM IS CORROSION IN FRONT WHEEL HUBS ON TONE RING.
    Remedy
    DEALER REPLACED BOTH FRONT SPEED SENSORS AND PROBLEM PERSISTS.

  4. Owner complaint2002 GMC YUKON ・ 2005-08-12

    ABS engagement with loss of brakes at low speeds

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    WHILE DRIVING AT LOW SPEEDS UNDER 5 MPH (= 8.05 km/h) ABS ENGAGED WHEN APPLYING BRAKES.
    Remedy
    TOOK VEHICLE TO THE DEALER FOR REPAIRS AND THE LEFT FRONT WHEEL HUB BEARING ASSEMBLY WAS REPLACED ALONG WITH THE WHEEL SPEED SENSOR.
    Outcome
    SINCE THIS REPAIRS THE PROBLEM HAS BEEN CORRECTED.

  5. Owner complaint2002 GMC YUKON ・ 2009-11-18

    ABS brakes activate at slow speeds causing vehicle to lurch forward

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    MY 2002 GMC YUKON HAS THE PROBLEM THAT WHEN STOPPING AT SLOW SPEEDS THE ABS BRAKES ACTIVATE CAUSING THE CAR TO LURCH FORWARD BEFORE COMING TO A COMPLETE STOP.
    Remedy
    EACH TIME IT WAS REPAIRED BY REMOVING AND CLEANING OR REPLACING THE SENSORS.

  6. Owner complaint2002 GMC YUKON DENALI ・ 2006-10-06

    ABS engaged while traveling at low speed

    1. 1Fault

    2. 2Finding the cause

      THERE WAS A NHTSA RECALL, # 05V379000, REGARDING THE ANTILOCK BRAKES.

    3. 3Correction

      Not stated

      What the documents say to do

      Unwanted ABS activation at low speed (front wheel speed sensor mounting corrosion)

      Confirm

      • The reading should be at least 350 mV AC; if it is less, the wheel speed sensor must be replaced.

      Repair

      1. Dealers remove the sensor, clean its mounting surface on the bearing, apply rust inhibitor and grease, reinstall it and check peak-to-peak output voltage.
      2. The passage heading states that the repair is cleaning the wheel speed sensor mounting surface.

      Caution

      • Do not pry the sensor out of the bore; prying breaks the sensor body off in the bore.
    Read the sentences of the record
    Fault
    DT*: THE CONTACT STATED WHILE TRAVELING 10 MPH (= 16.1 km/h), THE ABS ENGAGED.
    Cause
    THERE WAS A NHTSA RECALL, # 05V379000, REGARDING THE ANTILOCK BRAKES.

  7. Owner complaint2000 GMC YUKON ・ 2006-02-27

    ABS engaged during driving at 10 MPH

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Not stated

      What the documents say to do

      Unwanted ABS activation at low speed (front wheel speed sensor mounting corrosion)

      Confirm

      • The reading should be at least 350 mV AC; if it is less, the wheel speed sensor must be replaced.

      Repair

      1. Dealers remove the sensor, clean its mounting surface on the bearing, apply rust inhibitor and grease, reinstall it and check peak-to-peak output voltage.
      2. The passage heading states that the repair is cleaning the wheel speed sensor mounting surface.

      Caution

      • Do not pry the sensor out of the bore; prying breaks the sensor body off in the bore.
    Read the sentences of the record
    Fault
    DT*: THE CONTACT STATED WHILE DRIVING AT 10 MPH (= 16.1 km/h), THE ABS ENGAGED.
    Consequence
    AS A RESULT, THE STOPPING DISTANCE WAS INCREASED.

  8. Owner complaint2001 GMC YUKON ・ 2005-12-16

    ABS activates at low speeds, extending stopping distance

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      THE VEHICLE HAS NOT BEEN REPAIRED AT THIS TIME DUE TO THE EXCESSIVE EXPENSE.

      What the documents say to do

      Unwanted ABS activation at low speed (front wheel speed sensor mounting corrosion)

      Confirm

      • The reading should be at least 350 mV AC; if it is less, the wheel speed sensor must be replaced.

      Repair

      1. Dealers remove the sensor, clean its mounting surface on the bearing, apply rust inhibitor and grease, reinstall it and check peak-to-peak output voltage.
      2. The passage heading states that the repair is cleaning the wheel speed sensor mounting surface.

      Caution

      • Do not pry the sensor out of the bore; prying breaks the sensor body off in the bore.
    Read the sentences of the record
    Fault
    *AK UPDATE 1/11/2006 - THE ABS ACTIVATED AT LOW SPEEDS RESULTING IN EXTENDED STOPPING DISTANCE. *NM
    Remedy
    THE VEHICLE HAS NOT BEEN REPAIRED AT THIS TIME DUE TO THE EXCESSIVE EXPENSE.

  9. Owner complaint2001 GMC YUKON ・ 2005-05-24

    ABS activates at low speed, causing extended stopping distances

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    DT: CONTACT STATES THE ABS COMES ON WHILE DRIVING APPROXIMATELY 5 MPH (= 8.05 km/h), CAUSING THE MANUAL BRAKES TO PUMP AT LOW SPEED, LEADING TO EXTENDED STOPPING DISTANCES. (1 more)
    Remedy
    THE SERVICE DEALER REPLACED THE RIGHT FRONT HUB AND THE SENSOR.

  10. Owner complaint2000 GMC YUKON ・ 2004-09-21

    ABS engages on dry pavement, pedal goes to floor, increasing braking distance

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Not stated

      What the documents say to do

      Unwanted ABS activation at low speed (front wheel speed sensor mounting corrosion)

      Confirm

      • The reading should be at least 350 mV AC; if it is less, the wheel speed sensor must be replaced.

      Repair

      1. Dealers remove the sensor, clean its mounting surface on the bearing, apply rust inhibitor and grease, reinstall it and check peak-to-peak output voltage.
      2. The passage heading states that the repair is cleaning the wheel speed sensor mounting surface.

      Caution

      • Do not pry the sensor out of the bore; prying breaks the sensor body off in the bore.
    Read the sentences of the record
    Fault
    WHILE APPLYING THE BRAKE THE ABS WOULD ENGAGE AND THE PEDAL WOULD GO TO THE FLOOR, INCREASING BRAKING DISTANCE. (1 more)
    Inspection
    I HAVE TAKEN IT TO A DEALER AND PRIVATE SHOPS AND NO ONE CAN FIND THE PROBLEM.*AK
    Consequence
    IN ONE INSTANCE MY WIFE WAS PARKING AND THE ABS ENGAGED AND THE YUKON RAN INTO THE CONCRETE PARKING BLOCK BECAUSE IT WOULDN'T STOP.

  11. Owner complaint2001 GMC YUKON ・ 2006-01-11

    ABS activated at low speeds; wheel speed sensor replaced twice

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

Known issuesBrake pipe (brake line) corrosion and rupture3

  1. Owner complaint2000 GMC YUKON ・ 2014-01-23

    Brake failure and ABS activation while driving, brake line corroded

    1. 1Fault

    2. 2Finding the cause

    3. 3CorrectionNot repaired

    Read the sentences of the record
    Fault
    THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 5 MPH (= 8.05 km/h), THE BRAKES FAILED TO ENGAGE WHEN DEPRESSED AND THE BRAKE PEDAL ABNORMALLY TRAVELED TO THE FLOOR BOARD. (1 more)
    Remedy
    THE VEHICLE WAS NOT REPAIRED. (1 more)
    Inspection
    THE VEHICLE WAS TAKEN TO A DEALER WHERE IT WAS DISCOVERED THAT THE BRAKE LINE WAS CORRODED.

  2. Owner complaint2002 GMC YUKON ・ 2015-04-20

    Brake failure with ABS activation and brake pedal vibration on several occasions

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    ON SEVERAL OCCASIONS WHEN APPLYING BRAKES TO STOP THE YUKON IT FAILS TO STOP AND THEN ABS KICKS IN CAUSING BRAKE PEDAL TO VIBRATE AND LOSS OF PRESSURE IN BRAKE PEDAL THEN TRUCK DOES NOT STOP IT SLIDES.
    Remedy
    I HAVE REPLACED MASTER CYLINDER DID NOT HELP, TRUCK NEEDS ALL NEW BRAKE LINES DUE TO RUST.

  3. Owner complaint2002 GMC YUKON ・ 2013-09-20

    Rear main brake line broke during hard stop on interstate

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Remedy
    SOON AS I SAW A STORE I STOPPED AND PURCHASED 4 CANS OF BRAKE FLUID REFILLED THE RESERVOIR AND MADE IT HOME WITH THAT.
    Inspection
    I JACKED MY YUKON UP AND SAW A VERY RUSTY STEEL LINE BROKE OFF AT THE FITTING IT DIDN'T PULL OUT OF THE FITTING IT ACTUALLY BROKE INTO AND OF COURSE FLUID WAS EVERYWHERE.

SERVICE BRAKES, HYDRAULIC4

  1. Owner complaint2001 GMC YUKON ・ 2005-07-31

    ABS activation caused swerving during braking over railroad tracks

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      NOTHING HAS BEEN DONE TO FIX THIS PROBLEM. *NM

    Read the sentences of the record
    Fault
    I WAS GOING ABOUT 25-30 MPH (= 40.2–48.3 km/h).
    Remedy
    NOTHING HAS BEEN DONE TO FIX THIS PROBLEM. *NM
    Consequence
    I HIT THE GUARD RAIL WITH THE RIGHT FRONT QUARTER CAUSING $3500 IN DAMAGE.

  2. Owner complaint2002 GMC YUKON ・ 2009-02-19

    ABS activates and prevents complete stop while driving at 15 MPH

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      THE VEHICLE HAS NOT YET BEEN REPAIRED.

    Read the sentences of the record
    Fault
    WHILE DRIVING 15 MPH (= 24.1 km/h), THE ABS ACTIVATES AND PREVENTS THE VEHICLE FROM COMING TO A COMPLETE STOP WHEN NEEDED.
    Remedy
    THE VEHICLE HAS NOT YET BEEN REPAIRED.

  3. Owner complaint2001 GMC YUKON ・ 2005-10-03

    ABS brakes engaged at low speeds

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      BUT, DID NOT HAVE THE VEHICLE FIXED.

    Read the sentences of the record
    Fault
    DT: THE CONSUMER STATED THAT THE ABS BRAKES ENGAGED AT LOW SPEEDS, 25 MPH (= 40.2 km/h). (1 more)
    Remedy
    BUT, DID NOT HAVE THE VEHICLE FIXED.

  4. Owner complaint2001 GMC YUKON ・ 2005-09-29

    ABS light on and ABS motor running continuously while driving

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      THE MECHANIC UNHOOKED THE ABS MOTOR.

    Read the sentences of the record
    Fault
    DT: WHILE DRIVING ON THE INTERSTATE THE OWNER SAW THE ABS LIGHT COME ON AND DIDN'T KNOW WHAT IT WAS. (2 more)
    Remedy
    THE MECHANIC UNHOOKED THE ABS MOTOR.

SERVICE BRAKES1

  1. Owner complaint2003 GMC YUKON ・ 2015-10-14

    ABS activation and acceleration hesitation occurring every drive

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    IT OCCURS EVERY TIME I DRIVE MY CAR, EVERY TIME I ACCELERATE AND BRAKE. (2 more)
    Cause
    APPARENTLY, THIS IS CAUSED BY A CORRODED MOUNTING SURFACE FOR THE FRONT WHEEL SPEED SENSORS. (2 more)
    Consequence
    HAZARD:THIS CAN CAUSE INCREASED STOPPING DISTANCES DURING LOW-SPEED BRAKE APPLICATIONS, WHICH COULD RESULT IN A CRASH.

2 owner complaints have no classified sentences yet, so their causes and repairs are not picked out. Their text is in the list of records.