Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon XL 2000–2006

GMC Yukon XLModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:

Possible causes

Check engine / Service Engine Soon, C03270 records
Transmission and driveline
Electrical, wiring and power
Engine
Exhaust and emissions
Fuel system
0Transfer case service light, New Venture Gear transfer case (replace the encoder motor sensor and reprogram the TCCM)0Intermittent MIL, service lamps/messages or DTCs from connector fretting corrosion0Reduced Engine Power from throttle body connector crimp, broken wire or grounds0Crankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-5218.1L only0Intake manifold gasket leak (cold idle misfire, lean codes)0Single-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring0P0300 after engine repairs: injector connectors crossed (cylinders 5-7 / 6-8)0Rear bank knock sensor corrosion from water intrusion (P0332)4.8L, 5.3L, 6.0L only0P0420 / P0430 on a new or just-replaced catalytic converter (break-in not completed)0Fuel module reservoir assembly: fuel pump wire connectors may overheat - recall 05V-1551500 only0DTC P0446 set with the SES lamp on (replace the EVAP vent solenoid, not the canister)
1 causes not drawn

The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.

FaultCrate・GMC Yukon XL 2000–2006・Check engine / Service Engine Soon, C0327

Candidate cause (the documents say what to do)

Transfer case service light, New Venture Gear transfer case (replace the encoder motor sensor and reprogram the TCCM)

0 of the records matching this search name this component as the cause.

How to tell

C0327P0500P0836Service 4WD

What to do

  1. Verify that the encoder motor is the primary cause.
  2. Replace the encoder motor sensor and reprogram the TCCM; the labor operation is K9980.

Caution: Do not replace the module, the encoder motor or the transfer case for DTCs C0327, P0836, P0500; the reference is bulletin 03-04-21-001D.

What is needed

Parts and materials
  • Encoder motor sensor
Labor time
  • Labor Operation: K9980
Special tools
Not stated
Scan tool
  • Reprogramming of the TCCM

Only what the technical documents state. "Not stated" does not mean not needed.

In the records

No record states work done for this cause.

See the evidence (1 technical documents, 0 records)

Passages of the technical documents

  • Row for 2003 Fullsize Pickups and Utilities: transfer case service light, New Venture Gear transfer case.

    2003 Fullsize Pickups and Utilities – Transfer Case Service Light/New Venture Gear Transfer Case

    General Motors 2004-04-01

  • Verify that the encoder motor is the primary cause.

    Verify that the encoder motor is the primary cause.

    General Motors 2004-04-01

  • Replace the encoder motor sensor and reprogram the TCCM; the labor operation is K9980.

    Replace encoder motor sensor and reprogram TCCM. Labor Operation: K9980

    General Motors 2004-04-01

  • Do not replace the module, the encoder motor or the transfer case for DTCs C0327, P0836, P0500; the reference is bulletin 03-04-21-001D.

    Don’t replace the module, encoder motor or transfer case for DTCs C0327, P0836, P0500 03-04-21-001D

    General Motors 2004-04-01

Read every statement and its source →

Records

None among the records that can be opened now.

See all 0 records of this cause →

A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.

Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.