Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon XL 2000–2006

GMC Yukon XLModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

Common on this vehicle:Warning lightMisfire or rough idleLoss of engine power, no accelerationStalls or shuts offLeakNoiseGauge or instrument faultHard start or long crank

Record by record

10 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (7)

Known issuesSingle-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring2

  1. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15(2 earlier editions of this document folded here)

    Engine Misfire and Service Engine Soon Lamp Information

    1. 1Fault

      • With the SES light on, a P0300-P0308 DTC is found with misfires counting on a single cylinder, which may or may not be felt.
      • The noise may be described as a chirp, squeak, squeal or tick and may increase off of idle.

    2. 2Finding the cause

      Possible causes

      • A worn cam lobe on this engine family generally makes a consistent chirp, squeak, squeal or tick at camshaft speed and/or a misfire with a P0300-P0308 DTC.

      Steps to confirm (in the document’s order)

      1. Press on the rocker arms with a wooden hammer handle while the noise is present; if pressing the valve side of a rocker changes the noise, a lifter and/or cam lobe concern on that cylinder is most likely.
      2. Measure cam lobe lift at the push rod side of the rocker arm; it will differ from the SI specification but should be similar to the other rockers on the same bank.
      3. A bore scope or pen light may help when inspecting the cam lobes through the lifter bores.
      4. A good sign of a sticking valve is that misfires keep counting during an aggressive deceleration with engine braking.
      5. The Cylinder Leakage Test in SI should typically isolate valve leakage by showing excessive leakage past an intake or exhaust valve compared with the others.
      1 more points

    3. 3Correction

      Repair

      1. If a worn cam lobe or lifter roller is found, replace the camshaft and all lifters per SI, plus the plastic lifter guide for the affected lifter (for the 2010 model year, all the plastic lifter guides).
      2. If force is needed to tap the valve off its seat, there is excessive carbon build up, which may be repaired by decarboning the engine.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 1999-2013 GMC Savana, Sierra and Yukon (with a V8 engine per the model list) (note: the Yukon years run later than the years this service covers).
    • Condition：With the SES light on, a P0300-P0308 DTC is found with misfires counting on a single cylinder, which may or may not be felt.
    • Condition：The noise may be described as a chirp, squeak, squeal or tick and may increase off of idle.
    • Cause：A worn cam lobe on this engine family generally makes a consistent chirp, squeak, squeal or tick at camshaft speed and/or a misfire with a P0300-P0308 DTC.
    • Confirm：Press on the rocker arms with a wooden hammer handle while the noise is present; if pressing the valve side of a rocker changes the noise, a lifter and/or cam lobe concern on that cylinder is most likely.
    • Confirm：Measure cam lobe lift at the push rod side of the rocker arm; it will differ from the SI specification but should be similar to the other rockers on the same bank.
    • Confirm：A bore scope or pen light may help when inspecting the cam lobes through the lifter bores.
    • Repair：If a worn cam lobe or lifter roller is found, replace the camshaft and all lifters per SI, plus the plastic lifter guide for the affected lifter (for the 2010 model year, all the plastic lifter guides).
    • Confirm：A good sign of a sticking valve is that misfires keep counting during an aggressive deceleration with engine braking.
    • Repair：If force is needed to tap the valve off its seat, there is excessive carbon build up, which may be repaired by decarboning the engine.
    • Confirm：The Cylinder Leakage Test in SI should typically isolate valve leakage by showing excessive leakage past an intake or exhaust valve compared with the others.
    • Confirm：The two pieces of a broken valve spring can stay stacked together and be hard to see, so lightly push on different places on the springs with a small hammer handle.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

  2. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15

    Service Engine Soon Lamp and Engine Misfire Information

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

      What the documents say to do

      Single-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring

      Confirm

      • If pressing on the valve side of the rocker changes the noise, a lifter and/or cam lobe concern on that cylinder is most likely.

      Repair

      1. If a worn camshaft lobe or lifter roller is found, follow SI procedures to replace the camshaft and all lifters.
      2. Also replace the plastic lifter guide for the lifter that had the damaged cam lobe and/or lifter roller.

      Caution

      • A damaged cam lobe is easy to overlook when inspecting through the lifter bores; unworn lifter rollers do not mean the cam lobes are okay.
    Read the sentences of the record

    Open the manufacturer’s document (PDF) ↗ What is shown here is NHTSA’s summary; the procedure is in the document itself.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

Known issuesFuel module reservoir assembly: fuel pump wire connectors may overheat - recall 05V-1551

  1. Recall2000–2001 GMC YUKON XL ・ —

    Fuel Module Reservoir Assembly Overheating Recall

    1. 1Fault

      • Some vehicles were built with fuel module reservoir assemblies whose fuel pump wires and/or connectors may overheat under certain operating conditions.
      • If the exposed ignition circuit wire shorts to ground, the fuel pump fuse blows, disabling the fuel pump and causing an engine stall or no-start; if the ignition circuit or ground wire shorts to the fuel level sender card wires, fuel level readings may be inaccurate.
      • If enough heat reaches the pass-through connector, a hole may form in it, which may turn on the Service Engine Soon light during the emission system diagnostics routine; fuel vapor, and in some cases liquid fuel, may leak from the tank through the hole.
      • If enough fuel leaked out and an ignition source were present, a vehicle fire could occur.

    2. 2Finding the cause

      Possible causes

      • Fretting corrosion caused by vibration inside the tank was identified as the cause of high resistance within the fuel pump connector.

    3. 3Correction

      Repair

      1. Dealers remove the fuel tank, remove the fuel module reservoir assembly and install a new service kit, which includes a new pass-through connector and a wiring harness for the fuel pump and fuel sender card.
      2. Start by disconnecting the negative battery cable, then remove and discard the "ECM B" fuse.
      3. In the revised bulletin, the fuel and EVAP pipes are capped with J 41413-300, EVAP Cap/Plug Kit, to prevent fuel system contamination.
      4. Remove the 4 pin Metri Pack 150 electrical connector from the vehicle's body harness.
      5. Connect the new GT280 connector to the vehicle's body harness with the 4 butt splice connectors contained in the kit.
      2 more points

      Parts

      • Part number 15824379, Harness Kit, F/Tnk F/Pmp Mdl Wrg, quantity 1 per vehicle.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Do not handle the fuel sender assembly by the fuel pipes; the leverage could damage the joints.
      • Always replace the fuel sender gasket when reinstalling the fuel sender assembly, to reduce the risk of fire and injury from a fuel leak.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The recall covers certain 2000-2001 Chevrolet 1500 Series Suburban and GMC 1500 Series Yukon XL vehicles built within the listed VIN breakpoints.
    • Condition：Some vehicles were built with fuel module reservoir assemblies whose fuel pump wires and/or connectors may overheat under certain operating conditions.
    • Condition：If the exposed ignition circuit wire shorts to ground, the fuel pump fuse blows, disabling the fuel pump and causing an engine stall or no-start; if the ignition circuit or ground wire shorts to the fuel level sender card wires, fuel level readings may be inaccurate.
    • Condition：If enough heat reaches the pass-through connector, a hole may form in it, which may turn on the Service Engine Soon light during the emission system diagnostics routine; fuel vapor, and in some cases liquid fuel, may leak from the tank through the hole.
    • Condition：If enough fuel leaked out and an ignition source were present, a vehicle fire could occur.
    • Cause：Fretting corrosion caused by vibration inside the tank was identified as the cause of high resistance within the fuel pump connector.
    • Repair：Dealers remove the fuel tank, remove the fuel module reservoir assembly and install a new service kit, which includes a new pass-through connector and a wiring harness for the fuel pump and fuel sender card.
    • Parts：Part number 15824379, Harness Kit, F/Tnk F/Pmp Mdl Wrg, quantity 1 per vehicle.
    • Repair：Start by disconnecting the negative battery cable, then remove and discard the "ECM B" fuse.
    • Repair：In the revised bulletin, the fuel and EVAP pipes are capped with J 41413-300, EVAP Cap/Plug Kit, to prevent fuel system contamination.
    • Caution：Do not handle the fuel sender assembly by the fuel pipes; the leverage could damage the joints.
    • Caution：Always replace the fuel sender gasket when reinstalling the fuel sender assembly, to reduce the risk of fire and injury from a fuel leak.
    • Repair：Remove the 4 pin Metri Pack 150 electrical connector from the vehicle's body harness.
    • Repair：Connect the new GT280 connector to the vehicle's body harness with the 4 butt splice connectors contained in the kit.
    • Repair：Install the fuel tank strap attaching bolts and tighten them to 40 N·m (30 lb ft).
    • Repair：Install the new fuel pump fuse contained in the kit into the vehicle's electrical center (ECM B).
    Cause
    CERTAIN TRUCKS AND SPORT UTILITY VEHICLES WERE BUILT WITH FUEL MODULE RESERVOIR ASSEMBLIES THAT CONTAIN FUEL PUMP WIRES CONNECTORS MAY OVERHEAT UNDER CERTAIN OPERATING CONDITIONS.
    Remedy
    DEALERS WILL REMOVE THE FUEL TANK, AND REMOVE THE MODULE RESERVOIR ASSEMBLIES FROM THE TANK, AND INSTALL A NEW SERVICE KIT FREE OF CHARGE. AN INTERIM LETTER TO OWNERS WAS MAILED ON MAY 25, 2005. THE OWNERS WERE RE-NOTIFIED ON OCTOBER 19, 2005, SINCE PARTS ARE NOW AVAILABE. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 AND GMC AT 1-866-996-9463.
    Consequence
    IF THE IGNITION CIRCUIT WIRE IS EXPOSED, THE FUEL PUMP FUSE WILL BLOW, DISABLING THE FUEL PUMP AND CAUSING AN ENGINE STALL OR NO-START CONDITION. IF SUFFICIENT HEAT IS CONDUCTED TO THE PASS-THROUGH CONNECTOR, A HOLE IN THE CONNECTOR MAY RESULT, WHICH MAY CAUSE A 'SERVICE ENGINE SOON' LIGHT TO BE ILLUMINATED DURING THE EMISSION SYSTEM DIAGNOSTIC ROUTINE. FUEL VAPOR AND IN SOME CASES LIQUID FUEL MAY LEAK OUT OF THE FUEL TANK THROUGH THE HOLE IN THE CONNECTOR BODY. FUEL LEAKAGE, IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN A FIRE. ALSO IF THE IGNITION CIRCUIT OR GROUND WIRE IS EXPOSED AND SHORTS TO THE FUEL LEVEL SENDER CARD WIRES, INACCURATE FUEL LEVEL READINGS MAY RESULT.

ENGINE AND ENGINE COOLING3

  1. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15(1 earlier editions of this document folded here)

    Engine Check Lamp P0442 Evaporative Emissions System Notification

    1. 1Fault

      • The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
      2. If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
      3. If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
      4. With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
      5. Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
      1 more points

    3. 3Correction

      Repair

      • If smoke passes through the purge solenoid, replace the purge solenoid.

      Caution

      • After verifying P0442, do not disturb any fuel system component before testing.
      • Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
      • A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2016 and prior passenger cars and trucks.
    • Condition：The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.
    • Caution：After verifying P0442, do not disturb any fuel system component before testing.
    • Confirm：With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
    • Confirm：If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
    • Repair：If smoke passes through the purge solenoid, replace the purge solenoid.
    • Confirm：If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
    • Confirm：With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
    • Confirm：Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
    • Confirm：If smoke testing finds nothing, the leak may exist only under vacuum: use the scan tool Purge/Seal function to pull a vacuum and watch the FTP sensor parameter for vacuum decay.
    • Caution：Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
    • Caution：A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

  2. Owner complaint2006 GMC YUKON DENALI XL ・ 2011-11-15

    Check engine light and exhaust manifold leak

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    RECENTLY, MY CHECK ENGINE LIGHT CAME ON IN MY 2006 YUKON DENALI XL W/ A 6.0 ENGINE. (1 more)
    Inspection
    THE DIAGNOSTIC TEST SHOWED A GAS CAP PROBLEM. (1 more)
    Outcome
    HOWEVER, THIS DID NOT FIX THE ISSUE.

  3. Owner complaint2003 GMC YUKON XL ・ 2010-07-21

    Manifold bolts broken on 2003 GMC Yukon XL

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    THE MANIFOLD BOLTS ARE BROKEN ON MY 2003 GMC YUKON XL.

ELECTRICAL1

  1. Recall2000–2001 GMC YUKON XL ・ 2005-04-15

    Fuel Module Reservoir Assembly Overheating Recall

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Cause
    Certain vehicles were built with fuel module reservoir assemblies that contain fuel pump wires and/or connectors that may overheat under certain operating conditions. Fuel pump wires that overheat may become exposed and result in one or more conditions; 1) If the ignition circuit wire is exposed and shorts to ground, the fuel pump fuse will blow, disabling the fuel pump and causing an engine stall or no-start condition. 2) If sufficient heat is conducted to the pass-through connector, a hole in the connector may result, which may cause the Service Engine Soon light to be illuminated during the emission system diagnostics routine. Fuel vapour (and in some limited cases liquid fuel) may leak out of the fuel tank through the hole in the connector body. 3) If the ignition circuit or ground wire is exposed and shorts to the fuel level sender card wires, inaccurate fuel level readings may result. Correction: Dealers will affect repairs.

Showing 7 of the 10 you can open. Narrow the search to see the rest.