Skip to content
FaultCrate
日本語Open preview: everything readable

This is an open preview: every record can be read without an account. The details of the plans are in preparation.

GMC Yukon XL 2000–2006

GMC Yukon XLModel years 2000–2006

Change vehicle →
Clear the search
1 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:Warning lightMisfire or rough idleLoss of engine power, no accelerationStalls or shuts offLeakNoiseGauge or instrument faultHard start or long crank

Record by record

48 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Symptom

Component named as the cause

Work done

How it is said to have ended

  • says it held for a while4
  • says it came back2
  • says it did not fix it10
  • result not stated2

A ribbon is as wide as the records that state both of its ends (only the commonest are drawn). A record that names several symptoms or components runs through each. Orange is records that say the fault came back or was not fixed. Results come from owners’ reports only; one that does not say is “result not stated”. None of this is a likelihood of a cause or a rate at which work succeeds.

Read the records one by one (25)

Known issuesReduced Engine Power from throttle body connector crimp, broken wire or grounds3

  1. Owner complaint2003 GMC YUKON XL 2500 ・ 2010-03-10

    Service engine light and reduced power mode episodes since November 2008

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    SINCE NOVEMBER 2008, MY 2003 GMC YUKON XL 2500 HAS HAD EPISODES WHERE THE SERVICE ENGINE LIGHT COMES ON AND THE ENGINE GOES INTO REDUCED POWER MODE.
    Remedy
    I HAVE TAKEN IT TO NUMEROUS GM DEALERS TO FIX THE PROBLEM, AND THEY HAVE REPLACED THE THROTTLE BODY ASSEMBLE AND WIRING HARNESS MULTIPLE TIMES AND THE PROBLEM KEEPS RECURRING.
    Consequence
    THERE HAVE BEEN MANY CLOSE EPISODES WHERE WE WERE ALMOST IN AN ACCIDENT.

  2. Owner complaint2003 GMC YUKON XL 1500 ・ 2015-09-28

    Check engine light and reduced power warning with complete loss of acceleration, braking and steering

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    WHILE TRAVELING TO WORK MY VEHICLES CHECK ENGINE LIGHT CAME ON AND THE REDUCED POWER WARNING CAME ON AT WHICH TIME I HAD COMPLETE LOSS OF ACCELERATION, COMPLETE LOSS OF BRAKING, AND COMPLETE LOSS OF STEERING POWER. (1 more)
    Remedy
    I HAVE ALREADY REPLACED THE THROTTLE HOUSING AND HARNESS COMPONENTS, ACCELERATION PEDAL SENSOR AND YET THE ISSUE CONTINUES, SOMEONE IS GOING TO ( DIE ) BECAUSE OF GMC'S LACK OF CONCERN AND RESPONSIBILITY TO OWNERS OF THEIR PRODUCTS.

  3. Owner complaint2003 GMC YUKON XL 1500 ・ 2015-02-23

    Reduced engine power and service engine soon signals appearing repeatedly since September 2014

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

    Read the sentences of the record
    Fault
    "REDUCED ENGINE POWER" AND SERVICE ENGINE SOON SIGNALS APPEAR ON VEHICLE PANEL CAUSING ENGINE POWER TO BE REDUCED IN A MATTER OF SECONDS.
    Remedy
    THROTTLE BODY SENSOR REPLACED TWICE, THROTTLE BODY HARNESS REPLACED, ALL WIRES, AND SENSORS HAVE BEEN CLEANED AND THOROUGHLY INSPECTED.

Known issuesSingle-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring2

  1. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15(2 earlier editions of this document folded here)

    Engine Misfire and Service Engine Soon Lamp Information

    1. 1Fault

      • With the SES light on, a P0300-P0308 DTC is found with misfires counting on a single cylinder, which may or may not be felt.
      • The noise may be described as a chirp, squeak, squeal or tick and may increase off of idle.

    2. 2Finding the cause

      Possible causes

      • A worn cam lobe on this engine family generally makes a consistent chirp, squeak, squeal or tick at camshaft speed and/or a misfire with a P0300-P0308 DTC.

      Steps to confirm (in the document’s order)

      1. Press on the rocker arms with a wooden hammer handle while the noise is present; if pressing the valve side of a rocker changes the noise, a lifter and/or cam lobe concern on that cylinder is most likely.
      2. Measure cam lobe lift at the push rod side of the rocker arm; it will differ from the SI specification but should be similar to the other rockers on the same bank.
      3. A bore scope or pen light may help when inspecting the cam lobes through the lifter bores.
      4. A good sign of a sticking valve is that misfires keep counting during an aggressive deceleration with engine braking.
      5. The Cylinder Leakage Test in SI should typically isolate valve leakage by showing excessive leakage past an intake or exhaust valve compared with the others.
      1 more points

    3. 3Correction

      Repair

      1. If a worn cam lobe or lifter roller is found, replace the camshaft and all lifters per SI, plus the plastic lifter guide for the affected lifter (for the 2010 model year, all the plastic lifter guides).
      2. If force is needed to tap the valve off its seat, there is excessive carbon build up, which may be repaired by decarboning the engine.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 1999-2013 GMC Savana, Sierra and Yukon (with a V8 engine per the model list) (note: the Yukon years run later than the years this service covers).
    • Condition：With the SES light on, a P0300-P0308 DTC is found with misfires counting on a single cylinder, which may or may not be felt.
    • Condition：The noise may be described as a chirp, squeak, squeal or tick and may increase off of idle.
    • Cause：A worn cam lobe on this engine family generally makes a consistent chirp, squeak, squeal or tick at camshaft speed and/or a misfire with a P0300-P0308 DTC.
    • Confirm：Press on the rocker arms with a wooden hammer handle while the noise is present; if pressing the valve side of a rocker changes the noise, a lifter and/or cam lobe concern on that cylinder is most likely.
    • Confirm：Measure cam lobe lift at the push rod side of the rocker arm; it will differ from the SI specification but should be similar to the other rockers on the same bank.
    • Confirm：A bore scope or pen light may help when inspecting the cam lobes through the lifter bores.
    • Repair：If a worn cam lobe or lifter roller is found, replace the camshaft and all lifters per SI, plus the plastic lifter guide for the affected lifter (for the 2010 model year, all the plastic lifter guides).
    • Confirm：A good sign of a sticking valve is that misfires keep counting during an aggressive deceleration with engine braking.
    • Repair：If force is needed to tap the valve off its seat, there is excessive carbon build up, which may be repaired by decarboning the engine.
    • Confirm：The Cylinder Leakage Test in SI should typically isolate valve leakage by showing excessive leakage past an intake or exhaust valve compared with the others.
    • Confirm：The two pieces of a broken valve spring can stay stacked together and be hard to see, so lightly push on different places on the springs with a small hammer handle.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

  2. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15

    Service Engine Soon Lamp and Engine Misfire Information

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

      What the documents say to do

      Single-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring

      Confirm

      • If pressing on the valve side of the rocker changes the noise, a lifter and/or cam lobe concern on that cylinder is most likely.

      Repair

      1. If a worn camshaft lobe or lifter roller is found, follow SI procedures to replace the camshaft and all lifters.
      2. Also replace the plastic lifter guide for the lifter that had the damaged cam lobe and/or lifter roller.

      Caution

      • A damaged cam lobe is easy to overlook when inspecting through the lifter bores; unworn lifter rollers do not mean the cam lobes are okay.
    Read the sentences of the record

    Open the manufacturer’s document (PDF) ↗ What is shown here is NHTSA’s summary; the procedure is in the document itself.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

Known issuesP0420 / P0430 on a new or just-replaced catalytic converter (break-in not completed)1

  1. Manufacturer communication2004–2006 GMC YUKON XL ・ 2017-08-15(3 earlier editions of this document folded here)

    Service Engine Soon Light at Low Mileage Diagnostic Information

    1. 1Fault

      • An SES light may appear on low mileage vehicles or after a recent catalytic converter replacement.
      • DTCs P0420 and/or P0430 may be stored.

    2. 2Finding the cause

      Possible causes

      • After a converter replacement the engine run time restrictions are no longer in place because the vehicle is no longer new, so the converter may not complete a thorough break-in cycle, possibly resulting in a false DTC P0420 and/or P0430.

      Steps to confirm (in the document’s order)

      • On a new or low mileage vehicle, use the Tech 2 to verify engine run time on the Engine Hour Meter in the IPC data display.

    3. 3Correction

      Repair

      1. Clear the DTCs and perform the drive cycle described in the document.
      2. Drive cycle step: drive at sustained highway speed for 25 to 30 minutes, then stop.
      3. Drive cycle step: after the engine has been off for 1 minute, restart and resume highway speed for an additional 10 to 15 minutes.
      4. If the diagnostics do not pass after the drive cycle, perform SI diagnostics and repair as necessary.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The model list names 2004 - 2017 GMC Savana, Sierra, Sierra Hybrid, Yukon and Yukon Hybrid.
    • Condition：An SES light may appear on low mileage vehicles or after a recent catalytic converter replacement.
    • Condition：DTCs P0420 and/or P0430 may be stored.
    • Cause：After a converter replacement the engine run time restrictions are no longer in place because the vehicle is no longer new, so the converter may not complete a thorough break-in cycle, possibly resulting in a false DTC P0420 and/or P0430.
    • Confirm：On a new or low mileage vehicle, use the Tech 2 to verify engine run time on the Engine Hour Meter in the IPC data display.
    • Repair：Clear the DTCs and perform the drive cycle described in the document.
    • Repair：Drive cycle step: drive at sustained highway speed for 25 to 30 minutes, then stop.
    • Repair：Drive cycle step: after the engine has been off for 1 minute, restart and resume highway speed for an additional 10 to 15 minutes.
    • Repair：If the diagnostics do not pass after the drive cycle, perform SI diagnostics and repair as necessary.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster  Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.

Known issuesCrankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-5211

  1. Recall2001 GMC YUKON XL ・ 2007-11-09

    Crankshaft Position Sensor Failure Recall

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

      What the documents say to do

      Crankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-521

      Repair

      1. Dealers replace the crankshaft position sensor.
      2. As the remedy, an improved CKP is installed.

      Caution

      • All of the surveyed consumers noted multiple stalling events before the CKP was properly diagnosed and replaced.
    Read the sentences of the record
    Cause
    On certain vehicles equipped with an 8.1L engine, the crankshaft position sensor may fail. If the sensor operates intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool-down period. If the sensor becomes inoperable permanently, the engine will quit running and will not re-start. Engine stalling would result in lost propulsion which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash. Correction: Dealers will replace the crankshaft position sensor.

Known issuesFuel module reservoir assembly: fuel pump wire connectors may overheat - recall 05V-1551

  1. Recall2000–2001 GMC YUKON XL ・ —

    Fuel Module Reservoir Assembly Overheating Recall

    1. 1Fault

      • Some vehicles were built with fuel module reservoir assemblies whose fuel pump wires and/or connectors may overheat under certain operating conditions.
      • If the exposed ignition circuit wire shorts to ground, the fuel pump fuse blows, disabling the fuel pump and causing an engine stall or no-start; if the ignition circuit or ground wire shorts to the fuel level sender card wires, fuel level readings may be inaccurate.
      • If enough heat reaches the pass-through connector, a hole may form in it, which may turn on the Service Engine Soon light during the emission system diagnostics routine; fuel vapor, and in some cases liquid fuel, may leak from the tank through the hole.
      • If enough fuel leaked out and an ignition source were present, a vehicle fire could occur.

    2. 2Finding the cause

      Possible causes

      • Fretting corrosion caused by vibration inside the tank was identified as the cause of high resistance within the fuel pump connector.

    3. 3Correction

      Repair

      1. Dealers remove the fuel tank, remove the fuel module reservoir assembly and install a new service kit, which includes a new pass-through connector and a wiring harness for the fuel pump and fuel sender card.
      2. Start by disconnecting the negative battery cable, then remove and discard the "ECM B" fuse.
      3. In the revised bulletin, the fuel and EVAP pipes are capped with J 41413-300, EVAP Cap/Plug Kit, to prevent fuel system contamination.
      4. Remove the 4 pin Metri Pack 150 electrical connector from the vehicle's body harness.
      5. Connect the new GT280 connector to the vehicle's body harness with the 4 butt splice connectors contained in the kit.
      2 more points

      Parts

      • Part number 15824379, Harness Kit, F/Tnk F/Pmp Mdl Wrg, quantity 1 per vehicle.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Do not handle the fuel sender assembly by the fuel pipes; the leverage could damage the joints.
      • Always replace the fuel sender gasket when reinstalling the fuel sender assembly, to reduce the risk of fire and injury from a fuel leak.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The recall covers certain 2000-2001 Chevrolet 1500 Series Suburban and GMC 1500 Series Yukon XL vehicles built within the listed VIN breakpoints.
    • Condition：Some vehicles were built with fuel module reservoir assemblies whose fuel pump wires and/or connectors may overheat under certain operating conditions.
    • Condition：If the exposed ignition circuit wire shorts to ground, the fuel pump fuse blows, disabling the fuel pump and causing an engine stall or no-start; if the ignition circuit or ground wire shorts to the fuel level sender card wires, fuel level readings may be inaccurate.
    • Condition：If enough heat reaches the pass-through connector, a hole may form in it, which may turn on the Service Engine Soon light during the emission system diagnostics routine; fuel vapor, and in some cases liquid fuel, may leak from the tank through the hole.
    • Condition：If enough fuel leaked out and an ignition source were present, a vehicle fire could occur.
    • Cause：Fretting corrosion caused by vibration inside the tank was identified as the cause of high resistance within the fuel pump connector.
    • Repair：Dealers remove the fuel tank, remove the fuel module reservoir assembly and install a new service kit, which includes a new pass-through connector and a wiring harness for the fuel pump and fuel sender card.
    • Parts：Part number 15824379, Harness Kit, F/Tnk F/Pmp Mdl Wrg, quantity 1 per vehicle.
    • Repair：Start by disconnecting the negative battery cable, then remove and discard the "ECM B" fuse.
    • Repair：In the revised bulletin, the fuel and EVAP pipes are capped with J 41413-300, EVAP Cap/Plug Kit, to prevent fuel system contamination.
    • Caution：Do not handle the fuel sender assembly by the fuel pipes; the leverage could damage the joints.
    • Caution：Always replace the fuel sender gasket when reinstalling the fuel sender assembly, to reduce the risk of fire and injury from a fuel leak.
    • Repair：Remove the 4 pin Metri Pack 150 electrical connector from the vehicle's body harness.
    • Repair：Connect the new GT280 connector to the vehicle's body harness with the 4 butt splice connectors contained in the kit.
    • Repair：Install the fuel tank strap attaching bolts and tighten them to 40 N·m (30 lb ft).
    • Repair：Install the new fuel pump fuse contained in the kit into the vehicle's electrical center (ECM B).
    Cause
    CERTAIN TRUCKS AND SPORT UTILITY VEHICLES WERE BUILT WITH FUEL MODULE RESERVOIR ASSEMBLIES THAT CONTAIN FUEL PUMP WIRES CONNECTORS MAY OVERHEAT UNDER CERTAIN OPERATING CONDITIONS.
    Remedy
    DEALERS WILL REMOVE THE FUEL TANK, AND REMOVE THE MODULE RESERVOIR ASSEMBLIES FROM THE TANK, AND INSTALL A NEW SERVICE KIT FREE OF CHARGE. AN INTERIM LETTER TO OWNERS WAS MAILED ON MAY 25, 2005. THE OWNERS WERE RE-NOTIFIED ON OCTOBER 19, 2005, SINCE PARTS ARE NOW AVAILABE. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 AND GMC AT 1-866-996-9463.
    Consequence
    IF THE IGNITION CIRCUIT WIRE IS EXPOSED, THE FUEL PUMP FUSE WILL BLOW, DISABLING THE FUEL PUMP AND CAUSING AN ENGINE STALL OR NO-START CONDITION. IF SUFFICIENT HEAT IS CONDUCTED TO THE PASS-THROUGH CONNECTOR, A HOLE IN THE CONNECTOR MAY RESULT, WHICH MAY CAUSE A 'SERVICE ENGINE SOON' LIGHT TO BE ILLUMINATED DURING THE EMISSION SYSTEM DIAGNOSTIC ROUTINE. FUEL VAPOR AND IN SOME CASES LIQUID FUEL MAY LEAK OUT OF THE FUEL TANK THROUGH THE HOLE IN THE CONNECTOR BODY. FUEL LEAKAGE, IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN A FIRE. ALSO IF THE IGNITION CIRCUIT OR GROUND WIRE IS EXPOSED AND SHORTS TO THE FUEL LEVEL SENDER CARD WIRES, INACCURATE FUEL LEVEL READINGS MAY RESULT.

ENGINE7

  1. Owner complaint2001 GMC YUKON XL 2500 ・ 2015-12-24

    Engine stalled at highway speeds without power steering or brakes

    1. 1Fault

    2. 2Finding the cause

      AFTER LOOKING AT AN ON-LINE FORUM, THE VEHICLE WITH THE 8.1 LITER ENGIN HAD SOME VEHICLES RECALLED WITH A CAM LOBE SENSOR FAULT WHICH CAUSES THIS TO HAPPEN. (1 more)

    3. 3Correction

      HOWEVER, WHEN THE VEHICLE WAS NEW, THEY HAD ALREADY REPLACE THE SAME PART WHEN THE VEHICLE WAS 3-5 MONTHS OLD.

    Read the sentences of the record
    Fault
    WHILE TRAVELING AT HIGHWAY SPEEDS THE ENGINE STOPPED WORKING / STALLED.
    Cause
    AFTER LOOKING AT AN ON-LINE FORUM, THE VEHICLE WITH THE 8.1 LITER ENGIN HAD SOME VEHICLES RECALLED WITH A CAM LOBE SENSOR FAULT WHICH CAUSES THIS TO HAPPEN. (1 more)
    Remedy
    HOWEVER, WHEN THE VEHICLE WAS NEW, THEY HAD ALREADY REPLACE THE SAME PART WHEN THE VEHICLE WAS 3-5 MONTHS OLD.

  2. Manufacturer communication2000–2006 GMC YUKON XL DENALI ・ 2024-07-16(1 earlier editions of this document folded here)

    Fuel Injection Cleaner Kit Service Bulletin

    1. 1Fault

      • Rough idle, crank no start, extended crank or misfire, with the engine warning lamp on and DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 set.
      • When the engine is cold, compression on multiple cylinders may be zero.
      • The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.

    2. 2Finding the cause

      Possible causes

      • Major carbon build-up on the intake and/or exhaust valves from fuel contamination or incomplete burning of the fuel; misfires should not appear before at least 8,000 km (5,000 mi).

    3. 3Correction

      Repair

      1. If there is no valve damage and no cam follower out of place, perform the cleaning procedure to free sticking valves and remove carbon from the valves and pistons.
      2. If valves are damaged or cam followers are out of place, make the engine mechanical repairs first and then perform the cleaning procedure to prevent a return.
      3. Fill Cleaner Kit J-35800-A with about 650 ml (22 oz, 2 cans) of Air Intake, Combustion Chamber Cleaner and set the air pressure at the tool to 260 kPa (40 psi).
      4. With GDS 2 or a scan tool, command engine idle to 2000 rpm so the engine does not stall.
      5. With the engine at operating temperature in a well-ventilated area, slowly and carefully induce the cleaner into the engine, taking about 3 minutes.

      Parts

      • The Top Engine Cleaning Kit (ACDelco Air Intake, Valve and Combustion Chamber Cleaner and ACDelco Fuel System Cleaner 44K) is 19435372 for the U.S. and Canada.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Inducing too much cleaner at too low an RPM, or stalling the engine with too much cleaner at once, may hydro-lock the engine and bend a connecting rod.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to GM passenger cars and trucks with gasoline engines only, model years 2000 to 2025.
    • Condition：Rough idle, crank no start, extended crank or misfire, with the engine warning lamp on and DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 set.
    • Condition：When the engine is cold, compression on multiple cylinders may be zero.
    • Condition：The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.
    • Cause：Major carbon build-up on the intake and/or exhaust valves from fuel contamination or incomplete burning of the fuel; misfires should not appear before at least 8,000 km (5,000 mi).
    • Repair：If there is no valve damage and no cam follower out of place, perform the cleaning procedure to free sticking valves and remove carbon from the valves and pistons.
    • Repair：If valves are damaged or cam followers are out of place, make the engine mechanical repairs first and then perform the cleaning procedure to prevent a return.
    • Caution：Inducing too much cleaner at too low an RPM, or stalling the engine with too much cleaner at once, may hydro-lock the engine and bend a connecting rod.
    • Repair：Fill Cleaner Kit J-35800-A with about 650 ml (22 oz, 2 cans) of Air Intake, Combustion Chamber Cleaner and set the air pressure at the tool to 260 kPa (40 psi).
    • Repair：With GDS 2 or a scan tool, command engine idle to 2000 rpm so the engine does not stall.
    • Repair：With the engine at operating temperature in a well-ventilated area, slowly and carefully induce the cleaner into the engine, taking about 3 minutes.
    • Parts：The Top Engine Cleaning Kit (ACDelco Air Intake, Valve and Combustion Chamber Cleaner and ACDelco Fuel System Cleaner 44K) is 19435372 for the U.S. and Canada.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

  3. Owner complaint2004 GMC YUKON XL ・ 2018-11-06

    Check engine light illuminated; transmission failure diagnosed

    1. 1Fault

    2. 2Finding the cause

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT REPAIRED.

    Read the sentences of the record
    Fault
    WHILE DRIVING 60 MPH (= 96.6 km/h), THE CHECK ENGINE WARNING INDICATOR ILLUMINATED.
    Remedy
    THE VEHICLE WAS NOT REPAIRED.
    Inspection
    THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE IT WAS DIAGNOSED THAT THE TRANSMISSION FAILED AND NEEDED TO BE REPLACED.

  4. Owner complaint2000 GMC YUKON XL ・ 2017-12-20

    Vehicle stalls while driving at 55 MPH with sputtering noise

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED.

    Read the sentences of the record
    Fault
    WHILE DRIVING 55 MPH (= 88.5 km/h), THE VEHICLE MADE A SPUTTERING NOISE AND STALLED. (1 more)
    Remedy
    THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED.

  5. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15(1 earlier editions of this document folded here)

    Engine Misfire and Rough Idle Malfunction Indicator Lamp

    1. 1Fault

      • Customers may complain of a MIL and/or engine misfire, rough idle, extended crank, or crank no start.
      • One or more misfire codes (DTC P0300-P0308) are found stored in the ECM.

    2. 2Finding the cause

      Possible causes

      • The condition may result from major carbon build up on the intake and/or exhaust valves due to fuel contamination or incomplete burning of the fuel.

      Steps to confirm (in the document’s order)

      1. With the engine cold, compression on multiple cylinders may read 0 PSI (= 0 kPa).
      2. The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.

    3. 3Correction

      Repair

      1. If there is valve damage or cam followers are out of place, make the mechanical repairs first, then perform the cleaning procedure to keep the concern from returning.
      2. With the engine at operating temperature, slowly induce a bottle of GM Upper Engine and Fuel Injection Cleaner with RPM held above idle so the engine does not stall (typically around 2,000 RPM).
      3. Turn the engine off and let the cleaner soak for 2.5 to 3 hours.
      4. To complete the repair, change the engine oil and filter.

      Parts

      • Upper Engine and Fuel Injector Cleaner is P/N 88861803 (in Canada, P/N 88861804).

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Inducing too much cleaner at too low an RPM, or stalling the engine with cleaner, may hydro-lock the engine and bend a connecting rod.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to all 2000-2015 light duty trucks with gasoline engines.
    • Condition：Customers may complain of a MIL and/or engine misfire, rough idle, extended crank, or crank no start.
    • Condition：One or more misfire codes (DTC P0300-P0308) are found stored in the ECM.
    • Cause：The condition may result from major carbon build up on the intake and/or exhaust valves due to fuel contamination or incomplete burning of the fuel.
    • Confirm：With the engine cold, compression on multiple cylinders may read 0 PSI (= 0 kPa).
    • Confirm：The engine may pop through the intake or exhaust while cranking, and the spark plugs may be fuel fouled.
    • Repair：If there is valve damage or cam followers are out of place, make the mechanical repairs first, then perform the cleaning procedure to keep the concern from returning.
    • Repair：With the engine at operating temperature, slowly induce a bottle of GM Upper Engine and Fuel Injection Cleaner with RPM held above idle so the engine does not stall (typically around 2,000 RPM).
    • Repair：Turn the engine off and let the cleaner soak for 2.5 to 3 hours.
    • Repair：To complete the repair, change the engine oil and filter.
    • Caution：Inducing too much cleaner at too low an RPM, or stalling the engine with cleaner, may hydro-lock the engine and bend a connecting rod.
    • Parts：Upper Engine and Fuel Injector Cleaner is P/N 88861803 (in Canada, P/N 88861804).

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

  6. Manufacturer communication2003–2006 GMC YUKON DENALI XL ・ 2017-05-16

    Engine Misfire and Rough Idle Diagnostic Communication

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

    Read the sentences of the record
    Remedy
    THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

  7. Owner complaint2005 GMC YUKON DENALI XL ・ 2013-06-17

    Brake failure during stopping with check engine light illumination

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3CorrectionNot repaired

      THE VEHICLE WAS NOT REPAIRED.

    Read the sentences of the record
    Fault
    THE CONTACT STATED THAT WHILE COMING TO A STOP, THE BRAKES FAILED AS THE CHECK ENGINE WARNING LIGHT ILLUMINATED.
    Remedy
    THE VEHICLE WAS NOT REPAIRED.
    Inspection
    THE VEHICLE WAS TAKEN TO A PRIVATE MECHANIC WHERE IT WAS DIAGNOSED THAT THE POWER STEERING CYLINDER, THE POWER STEERING HOSES, THE MASTER BRAKE CYLINDER, AND THE BRAKING SYSTEM NEEDED TO BE REPLACED.

ELECTRICAL SYSTEM4

  1. Owner complaint2003 GMC YUKON XL ・ 2010-02-16

    Vehicle stalls while in motion and when braking

    1. 1Fault

    2. 2Finding the cause

      FIGURED OUT IT MAY BE RUNNING OUT OF GAS DUE TO THE GAUGE NOT WORKING.

    3. 3Correction

    Read the sentences of the record
    Fault
    VEHICLE STALLS WHILE IN MOTION. (1 more)
    Cause
    FIGURED OUT IT MAY BE RUNNING OUT OF GAS DUE TO THE GAUGE NOT WORKING.
    Remedy
    REPLACED THE FUEL FILTER TWICE. (1 more)

  2. Manufacturer communication2005–2006 GMC YUKON XL ・ 2018-06-04(1 earlier editions of this document folded here)

    IP to Body Harness Connector Repair for MIL and DTC P2138

    1. 1Fault

      • The engine warning lamp comes on intermittently with a message or indicator showing Reduced Engine Power.
      • DTC P2138 (Accelerator Pedal Position (APP) Sensor 1-2 Correlation) is set as current or in history.

    2. 2Finding the cause

      Possible causes

      • Water may have entered the instrument panel (IP) to body harness connector, which carries the APP sensor signals to the ECM/PCM.

      Steps to confirm (in the document’s order)

      1. Verify that no aftermarket equipment is electrically connected to the APP sensor signal or low reference circuits, or to any other ECM/PCM 5V reference or low reference circuit.
      2. Locate the IP to body harness connector, which may be in or around the left hand kick panel area or inside the IP.
      3. Inspect for a water leak in the area, using a water hose if necessary to find the source.
      4. Possible water leak points include the A-pillar seals, the sunroof drain lines (if equipped) and the windshield/cowl sealing.
      5. Inspect the terminals of the IP to body harness connector for corrosion and debris.

    3. 3Correction

      Repair

      1. If a water leak is found, repair it as necessary and verify that the repair is effective.
      2. If corrosion or debris is found on the connector terminals, repair as necessary.

      Caution

      • Aftermarket equipment can generate DTC P2138 and/or other DTCs.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2018 and prior GM passenger cars and light duty trucks.
    • Condition：The engine warning lamp comes on intermittently with a message or indicator showing Reduced Engine Power.
    • Condition：DTC P2138 (Accelerator Pedal Position (APP) Sensor 1-2 Correlation) is set as current or in history.
    • Cause：Water may have entered the instrument panel (IP) to body harness connector, which carries the APP sensor signals to the ECM/PCM.
    • Caution：Aftermarket equipment can generate DTC P2138 and/or other DTCs.
    • Confirm：Verify that no aftermarket equipment is electrically connected to the APP sensor signal or low reference circuits, or to any other ECM/PCM 5V reference or low reference circuit.
    • Confirm：Locate the IP to body harness connector, which may be in or around the left hand kick panel area or inside the IP.
    • Confirm：Inspect for a water leak in the area, using a water hose if necessary to find the source.
    • Confirm：Possible water leak points include the A-pillar seals, the sunroof drain lines (if equipped) and the windshield/cowl sealing.
    • Repair：If a water leak is found, repair it as necessary and verify that the repair is effective.
    • Confirm：Inspect the terminals of the IP to body harness connector for corrosion and debris.
    • Repair：If corrosion or debris is found on the connector terminals, repair as necessary.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.

  3. Manufacturer communication2005 GMC YUKON XL ・ 2018-05-21(1 earlier editions of this document folded here)

    Throttle Position Sensor Cover Replacement

    1. 1Fault

      • The malfunction indicator lamp (MIL) is illuminated with a Reduced Engine Power message displayed.
      • A scan tool may show DTC P2135: Throttle Position (TP) Sensor 1-2 Correlation set as Current or in History.

    2. 2Finding the cause

      Possible causes

      • The condition may be caused by the difference between TP Sensor 1 and TP Sensor 2 exceeding a calibrated value for more than 2 seconds.

      Steps to confirm (in the document’s order)

      1. After installing the new cover, if the scan tool TP Sensor 1 and 2 Agree/Disagree parameter displays Disagree, replace the throttle body assembly.
      2. If DTC P1516, P2101 and/or P2176 are set, replace the throttle body.

    3. 3Correction

      Repair

      1. Clean the throttle body bore and throttle plate with a clean shop towel and GM Top Engine Cleaner, P/N 1052626 (in Canada, P/N 993026), or ACDelco Upper Engine and Fuel Injector Cleaner, P/N 88861803, or an equivalent product.
      2. Remove the old TP sensor cover from the throttle body: grasp the cover, carefully lift it up and separate it from the throttle body.
      3. Tighten the throttle body fasteners to 89 lb in (= 10.1 N·m) (the text prints the metric value as "10 Y").
      4. Reprogram the ECM using the Service Programming System (SPS) with the latest calibration available on TIS2WEB.
      5. Perform the Throttle Learn Reset Procedure.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Parts

      • Part number 19259452, Throttle Position (TP) Sensor Cover, quantity 1.

      Part numbers printed in the document

      The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

      Caution

      • Do not replace the throttle body; follow the procedure in the bulletin instead.
      • If the throttle body is dropped at any time during the procedure, abort the procedure and replace it with a new throttle body assembly.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：The Yukon entries are 2008-2011 GMC Canyon, Savana, Sierra, Sierra Denali and Yukon models (note: earlier Yukon model years are not listed).
    • Condition：The malfunction indicator lamp (MIL) is illuminated with a Reduced Engine Power message displayed.
    • Condition：A scan tool may show DTC P2135: Throttle Position (TP) Sensor 1-2 Correlation set as Current or in History.
    • Cause：The condition may be caused by the difference between TP Sensor 1 and TP Sensor 2 exceeding a calibrated value for more than 2 seconds.
    • Caution：Do not replace the throttle body; follow the procedure in the bulletin instead.
    • Repair：Clean the throttle body bore and throttle plate with a clean shop towel and GM Top Engine Cleaner, P/N 1052626 (in Canada, P/N 993026), or ACDelco Upper Engine and Fuel Injector Cleaner, P/N 88861803, or an equivalent product.
    • Repair：Remove the old TP sensor cover from the throttle body: grasp the cover, carefully lift it up and separate it from the throttle body.
    • Caution：If the throttle body is dropped at any time during the procedure, abort the procedure and replace it with a new throttle body assembly.
    • Confirm：After installing the new cover, if the scan tool TP Sensor 1 and 2 Agree/Disagree parameter displays Disagree, replace the throttle body assembly.
    • Confirm：If DTC P1516, P2101 and/or P2176 are set, replace the throttle body.
    • Repair：Tighten the throttle body fasteners to 89 lb in (= 10.1 N·m) (the text prints the metric value as "10 Y").
    • Repair：Reprogram the ECM using the Service Programming System (SPS) with the latest calibration available on TIS2WEB.
    • Repair：Perform the Throttle Learn Reset Procedure.
    • Parts：Part number 19259452, Throttle Position (TP) Sensor Cover, quantity 1.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set.

  4. Owner complaint2005 GMC YUKON DENALI XL ・ 2015-08-31

    Speedometer erratic reading and cruise control malfunction on highway

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

    Read the sentences of the record
    Fault
    WHILE DRIVING ON THE HIGHWAY WITH MY CRUISE CONTROL SET BETWEEN 50-70MPH (= 80.5–112.7 km/h), I BEGAN NOTICING MY SPEEDOMETER BEGINNING TO JUMP BETWEEN 0-120MPH (= 0–193.1 km/h) CAUSING THE LIMITER TO KICK IN AND ME LOSING THE ABILITY TO CONTROL SPEED. (4 more)
    Cause
    SOME HAD SIMILAR ISSUES AND SAID THE IGNITION COILS MAY BE BAD.
    Inspection
    I WAS TOLD THAT I HAD A BAD MASS AIR FLOW SENSOR. (1 more)

ENGINE AND ENGINE COOLING3

  1. Manufacturer communication2002–2006 GMC YUKON XL DENALI ・ 2023-04-13(1 earlier editions of this document folded here)

    Diagnostic tip on valve, lifter or camshaft issues

    1. 1Fault

      • Misfire, chirp, squeak, squeal or tick noise, with the MIL illuminated and DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 set.

    2. 2Finding the cause

      Possible causes

      • A worn cam lobe on this engine family generally creates a consistent chirp, squeak, squeal or tick at camshaft speed and/or a misfire with a P0300-P0308 DTC.

      Steps to confirm (in the document’s order)

      1. A verified noise is not eliminated by canceling fuel injectors and occurs at camshaft speed (half of crankshaft speed).
      2. If applying pressure to the valve side of a rocker changes the noise, a lifter and/or cam lobe concern on that cylinder is most likely.
      3. Measure cam lobe lift at the push rod side of the rocker arm; it differs from the SI specification but should be similar to the other rockers on the same bank.
      4. A bore scope or pen light helps when inspecting the cam lobes through the lifter bores; a damaged lobe is easy to overlook.
      5. A good indicator of a sticking valve is that misfires continue to count on an aggressive deceleration with engine braking.
      2 more points

    3. 3Correction

      Repair

      1. If a worn camshaft lobe or lifter roller is found, replace the camshaft and all lifters following SI procedures.
      2. If force is needed to tap the valve off its seat, excessive carbon build up exists, which may be repaired by decarbonizing the engine.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：GM passenger cars and trucks with V6/V8 pushrod engines, model years 2002 to 2023.
    • Condition：Misfire, chirp, squeak, squeal or tick noise, with the MIL illuminated and DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 set.
    • Confirm：A verified noise is not eliminated by canceling fuel injectors and occurs at camshaft speed (half of crankshaft speed).
    • Cause：A worn cam lobe on this engine family generally creates a consistent chirp, squeak, squeal or tick at camshaft speed and/or a misfire with a P0300-P0308 DTC.
    • Confirm：If applying pressure to the valve side of a rocker changes the noise, a lifter and/or cam lobe concern on that cylinder is most likely.
    • Confirm：Measure cam lobe lift at the push rod side of the rocker arm; it differs from the SI specification but should be similar to the other rockers on the same bank.
    • Confirm：A bore scope or pen light helps when inspecting the cam lobes through the lifter bores; a damaged lobe is easy to overlook.
    • Repair：If a worn camshaft lobe or lifter roller is found, replace the camshaft and all lifters following SI procedures.
    • Confirm：A good indicator of a sticking valve is that misfires continue to count on an aggressive deceleration with engine braking.
    • Repair：If force is needed to tap the valve off its seat, excessive carbon build up exists, which may be repaired by decarbonizing the engine.
    • Confirm：Valve leakage is typically isolated by the Cylinder Leakage Test in SI, which finds excessive leakage past an intake or exhaust valve compared with the others.
    • Confirm：The two pieces of a broken valve spring may stay stacked together and be hard to see; lightly pushing on different places on the springs with a small hammer handle may help.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.

  2. Manufacturer communication2000–2006 GMC YUKON XL ・ 2017-08-15(1 earlier editions of this document folded here)

    Engine Check Lamp P0442 Evaporative Emissions System Notification

    1. 1Fault

      • The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.

    2. 2Finding the cause

      Steps to confirm (in the document’s order)

      1. With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
      2. If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
      3. If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
      4. With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
      5. Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
      1 more points

    3. 3Correction

      Repair

      • If smoke passes through the purge solenoid, replace the purge solenoid.

      Caution

      • After verifying P0442, do not disturb any fuel system component before testing.
      • Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
      • A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to 2016 and prior passenger cars and trucks.
    • Condition：The service engine soon lamp (MIL) is on for DTC P0442, but a leak cannot be verified with the system test in the service information.
    • Caution：After verifying P0442, do not disturb any fuel system component before testing.
    • Confirm：With the scan tool, command the EVAP system CLOSED, start the engine and watch the tank pressure sensor value for about two minutes.
    • Confirm：If the tank pressure value changes (shows vacuum), remove the purge solenoid and pressurize its fuel tank side with the GE 41413-A / J 41413-A tester.
    • Repair：If smoke passes through the purge solenoid, replace the purge solenoid.
    • Confirm：If the tank pressure value does not change, install the CH-48096 adaptor between the purge line from the canister and the purge solenoid; use no other adaptor or pressurization method.
    • Confirm：With the EVAP system CLOSED, pressurize through the adaptor and let the system stabilize, watching the gauge for at least 5 minutes, then add smoke.
    • Confirm：Look for smoke or UV trace fluid at the purge solenoid, the engine side, the fuel cap or capless fill door, and the canister vent solenoid filter or fresh-air line.
    • Confirm：If smoke testing finds nothing, the leak may exist only under vacuum: use the scan tool Purge/Seal function to pull a vacuum and watch the FTP sensor parameter for vacuum decay.
    • Caution：Test pressure must not exceed 13 in H2O (0.5 PSI (= 3.45 kPa)); more can make components perform inaccurately and lead to misdiagnosis.
    • Caution：A large temperature difference between vehicle, shop and tester seriously affects accuracy; let the vehicle adjust to shop temperature first.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

  3. Owner complaint2006 GMC YUKON DENALI XL ・ 2011-11-15

    Check engine light and exhaust manifold leak

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    RECENTLY, MY CHECK ENGINE LIGHT CAME ON IN MY 2006 YUKON DENALI XL W/ A 6.0 ENGINE. (1 more)
    Inspection
    THE DIAGNOSTIC TEST SHOWED A GAS CAP PROBLEM. (1 more)
    Outcome
    HOWEVER, THIS DID NOT FIX THE ISSUE.

ELECTRICAL1

  1. Recall2000–2001 GMC YUKON XL ・ 2005-04-15

    Fuel Module Reservoir Assembly Overheating Recall

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Cause
    Certain vehicles were built with fuel module reservoir assemblies that contain fuel pump wires and/or connectors that may overheat under certain operating conditions. Fuel pump wires that overheat may become exposed and result in one or more conditions; 1) If the ignition circuit wire is exposed and shorts to ground, the fuel pump fuse will blow, disabling the fuel pump and causing an engine stall or no-start condition. 2) If sufficient heat is conducted to the pass-through connector, a hole in the connector may result, which may cause the Service Engine Soon light to be illuminated during the emission system diagnostics routine. Fuel vapour (and in some limited cases liquid fuel) may leak out of the fuel tank through the hole in the connector body. 3) If the ignition circuit or ground wire is exposed and shorts to the fuel level sender card wires, inaccurate fuel level readings may result. Correction: Dealers will affect repairs.

ELECTRONIC STABILITY CONTROL (ESC)1

  1. Owner complaint2003 GMC YUKON XL DENALI ・ 2012-12-18

    Power loss at 65 mph on highway, reduced engine power message, codes cleared but symptom persists

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    DRIVING 65 MPH (= 104.6 km/h) ON THE HIGHWAY AND ALL OF A SUDDEN MY CAR LOSES POWER. (2 more)
    Outcome
    I GOT EVERYTHING DONE THAT WAS SUGGESTED THE CODES ARE GONE AND IT'S STILL HAPPENING!!

UNKNOWN OR OTHER1

  1. Owner complaint2005 GMC YUKON XL 1500 ・ 2011-08-29

    Reduce Engine Power message and speed reduction, recurring after sensor replacement

    1. 1Fault

    2. 2Finding the cause

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    HELLO AROUND THE BEGINNING OF JUNE OF 2011 I WAS DRIVING MY 2005 GMC YUKON XL WHEN SUDDENLY I RECEIVED AN ERROR MESSAGE ON MY DASH BOARD STATING "REDUCE ENGINE POWER" AUTOMATICALLY MY SPEED WENT DOWN.
    Inspection
    I WAITED ABOUT 2 WEEKS AND TOOK IT IN AGAIN AND THIS TIME THEY CANNOT FIGURE OUT WHAT IS GOING ON WITH MY TRUCK, I EVEN LEFT IT THERE OVERNIGHT AND ALL THEY CAN TELL ME IS THAT THEY CANNOT FIGURE THE PROBLEM OUT.
    Consequence
    THIS IS AFFECTING MY EVERYDAY LIFE, I HAVE BEEN LATE TO MEETINGS, WORK, TO PICK UP MY DAUGHTER.

Showing 25 of the 48 you can open. Narrow the search to see the rest.

1 owner complaints have no classified sentences yet, so their causes and repairs are not picked out. Their text is in the list of records.