Manufacturer communication — 2006 GMC YUKON DENALI

• Applies to 2000-2014 GM passenger cars and light duty trucks and listed later models, including 2015 GMC Yukon models built without VV4, equipped with OnStar (RPO UE1).

  the passage

  2000-2014 GM Passenger Cars and Light Duty Trucks 2015 Buick Enclave 2015 Cadillac Escalade Models (Built W/O VV4) 2015 Chevrolet Camaro, Express, Traverse 2015 Chevrolet Silverado 2500/3500, Suburban, Tahoe (Built W/O VV4) 2012 Chevrolet Colorado 2015 GMC Acadia, Savana 2015 GMC Sierra 2500/3500, Yukon Models (Built W/O VV4) 2012 GMC Canyon 2005-2010 Pontiac Vibe Equipped with OnStar® (RPO UE1)

• Canadian wireless providers plan to decommission their 2G CDMA network through 2015, so Canadian vehicles without OnStar 3G/4G LTE need a hardware upgrade to keep OnStar services.

  the passage

  Canadian wireless service providers plan to decommission their 2G Code Division Multiple Access (CDMA) network through 2015. OnStar® currently depends on active and functioning 2G CDMA networks to deliver services. As a result, in order to continue to provide OnStar® services without interruption, Canadian vehicles that do not have OnStar® 3G/4G LTE will need a hardware upgrade.

Steps to confirm (in the document’s order)

• Before reprogramming, verify the battery voltage is more than 12 volts but less than 16 volts; the battery must be fully charged.

  the passage

  Verify the battery voltage is more than 12 volts but less than 16 volts before proceeding with reprogramming. The battery must be fully charged BEFORE reprogramming.

Repair

1. When installing module P/N 23230482 (one of the listed modules), transfer the Bluetooth antenna, if equipped, to the new module.

   the passage

   If installing the modules P/N 23230482, 23230536, 23230537, 23235220, 23235227, 23235234 and 23383877, transfer the Bluetooth Antenna (1), if equipped, to the new module.

2. If the vehicle requires a UHF adaptor cable (P/N 23242478), install it to the antenna connector of the module and install the female to male cable (P/N 23242476) to the module, then connect both to the vehicle cables.

   the passage

   If the vehicle requires a UHF adaptor cable (P/N 23242478) proceed with this step: 4.1. Install the UHF adapter cable (P/N 23242478) to the antenna connector (1) of the module. 4.2. Install the female to male cable (P/N 23242476) to the module (2). 4.3. Connect the UHF adapter (1) and the female to male (2) connector to the vehicle cables.

3. In SPS select 'Reprogram ECU' for Telematics Communication Interface Control Module programming even if the unit is being replaced.

   the passage

   Due to a change in SPS you must select ‘Reprogram ECU’, for Telematics Communication Interface Control Module Programming from the Selected Programming Process even if the unit is being replaced.

4. The vehicle must be located in an area with a strong cellular network to perform the OnStar Blue Button call step.

   the passage

   The vehicle must be located in an area with a strong cellular network to perform this step.

5. The labor time table lists 1.0 hr for 2003-2006 GMC Yukon models.

   the passage

   GMC Yukon Models 2003-2006 1.0 hr

Parts

• The parts chart row for 2003-2006 GMC Yukon models lists 23230482, 23242476 and 23242478.

  the passage

  2003-2006 GMC Yukon Models 23230482 23242476 23242478

Caution

• Hardware upgrade sets are VIN specific and must be installed on the vehicle the set was ordered for.

  the passage

  Hardware upgrade sets are VIN specific and must be installed on the vehicle that the set was ordered for.

• Make sure the ignition is off and RAP is deactivated before removing the OnStar module.

  the passage

  MAKE SURE IGNITION IS OFF AND RAP IS DEACTIVATED PRIOR TO REMOVAL OF THE ONSTAR® MODULE.

• Vehicles with voice recognition systems may have a performance issue after the upgrade; PI1533, Poor Radio Hands-free Voice Recognition Performance, is required to prevent it.

  the passage

  Vehicles with voice recognition systems may have a performance issue after the upgrade. “ PI1533 - Poor Radio Hands-free Voice Recognition Performance “ is required to prevent this issue.

• Do not press the red OnStar Emergency Button at any time during the installation; this causes module configuration issues, and if it is pressed inadvertently the final configuration with the advisor cannot be completed until the next day.

  the passage

  Do NOT press the RED (OnStar® Emergency Button) at any time during the installation. This will cause module configuration issues. If you inadvertently press the RED (OnStar® Emergency Button) during installation, you will not be able to complete the final configuration with the adviso until the next day.

• After programming, turn the ignition OFF and wait ten minutes; a 10 minute wait is required to avoid configuration errors.

  the passage

  Turn the ignition to the OFF position and wait ten minutes. Notice: A 10 minute wait time is required to avoid configuration errors.