Manufacturer communication — 2006 GMC YUKON DENALI XL

• The model list includes the 2001-2013 GMC Yukon, Yukon XL LD, Yukon Denali and Yukon Denali XL.

  the passage

  2001-2013 GMC Yukon, Yukon XL LD, Yukon Denali, Yukon Denali XL

• It applies to vehicles with RPO Z55 or Z95.

  the passage

  With RPO Z55 or Z95

• Condition 1: on 2009 or prior vehicles, a Service Suspension System message appears on the DIC and the rear suspension ride height is incorrect; the Electronic Suspension Control (ESC) module has DTC C0696 or C0711 set.

  the passage

  Some customers of 2009 or prior vehicles, may comment of a Service Suspension System message on the DIC and the rear suspension ride height is incorrect. When checking for DTCs the Electronic Suspension Control (ESC) module will have DTC C0696 or C0711 set.

• Condition 2: a Service Suspension System message appears on the DIC and the rear suspension ride height may be low under a heavy payload; the Electronic Suspension Control (ESC) module has DTC C0711 set.

  the passage

  Some customers may comment of a Service Suspension System message on the DIC and may also comment that the rear suspension ride height may be low under a heavy payload. When checking for DTCs the Electronic Suspension Control (ESC) module will have DTC C0711 set.

• Condition 3: a loose hose hangs down in the left rear of the vehicle; the hose may be damaged or disconnected from the air inlet filter of the auto leveling suspension air compressor.

  the passage

  Some customers may comment of a loose hose hanging down in the left rear of the vehicle. Upon inspection it may be determined that the hose is damaged or has become disconnected from the air inlet filter of the auto leveling suspension air compressor.

Possible causes

• This could be caused by the wiring to the automatic level control (ALC) pressure sensor being shorted to ground.

  the passage

  This concern could be caused by the wiring to the automatic level control (ALC) pressure sensor being shorted to ground

• This may be caused by an internal fault in the automatic level control (ALC) pressure sensor, which may occur due to moisture getting into the sensor.

  the passage

  This concern may be caused by an internal fault in the automatic level control (ALC) pressure sensor. This may occur due to moisture getting into the sensor.

• If the system pressure is below 10 psi (69 kpa) at start up, the system operates the compressor to add air to the shocks as a replenishment cycle.

  the passage

  If the pressure is below 10 psi (69 kpa) then the system will operate the compressor to add air to the shocks as a replenishment cycle.

Steps to confirm (in the document’s order)

• The air compressor assembly may need to be removed from the vehicle to determine whether the wiring is pinched between the compressor assembly and the frame.

  the passage

  The air compressor assembly may need to be removed from the vehicle to determine if the wiring is possibly pinched between the compressor assembly and frame.

Repair

1. Repair any damaged or shorted circuits and then reposition the wiring so it does not get damaged again during the compressor assembly installation.

   the passage

   Repair any damaged or shorted circuits and then reposition the wiring so it does not get damaged again during the compressor assembly installation.

2. The sensor is no longer serviced separately; for sensor replacement, install a complete air filter, dryer, and sensor assembly.

   the passage

   The sensor is no longer serviced separately. For sensor replacement, install a complete air filter, dryer, and sensor assembly.

3. For condition 3, replace the auto leveling compressor air inlet filter and hose assembly (PN 22197160).

   the passage

   Replace the auto leveling compressor air inlet filter and hose assembly (PN 22197160), shown below.

Parts

• Vehicles built before May, 2012 require a jumper harness for the updated sensor design; the jumper harness is included with the complete air filter, dryer, and sensor assembly, PN 22964558.

  the passage

  Vehicles built before May, 2012, will require a jumper harness for the updated sensor design. The jumper harness is included with complete air filter, dryer, and sensor assembly, PN 22964558.

Caution

• Do not replace the complete air compressor assembly for this concern.

  the passage

  DO NOT replace the complete air compressor assembly for this concern.

• Condition 4 (no compressor self test at start up): the automatic level system normally will not, or will only very infrequently, cycle the compressor at key up.

  the passage

  The automatic level system normally will not or very infrequently cycle the compressor at key up.