Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon 2000–2006

GMC YukonModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:Loss of engine power, no accelerationWarning lightVibration or shudder

causeThrottle BodyRemove

Possible causes

Warning light, Engine2 records
Engine
Brakes
Transmission and driveline
Electrical, wiring and power
Exhaust and emissions
Fuel system
2Throttle Body: failed0Crankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-5218.1L only0Intake manifold gasket leak (cold idle misfire, lean codes)0Single-cylinder misfire (P0300-P0308) and/or chirp, squeak or tick at camshaft speed: worn cam lobe / lifter, valve or valve spring0P0300 after engine repairs: injector connectors crossed (cylinders 5-7 / 6-8)0Rear bank knock sensor corrosion from water intrusion (P0332)4.8L, 5.3L, 6.0L only0Brake pipe (brake line) corrosion and rupture0ABS light with C0265/C0201/U1041 or no communication with brake module (EBCM ground G110)0Front right-hand brake pipe contact with body cross sill - recall 00V-3450Service Brake Booster message on a Hydroboost vehicle with DTC C0136 (instrument cluster not SPS programmed)0Stability System Disabled / Service Stability message with DTC C0455 (bent terminals at the steering wheel position sensor)0Transfer case service light, New Venture Gear transfer case (replace the encoder motor sensor and reprogram the TCCM)0Intermittent MIL, service lamps/messages or DTCs from connector fretting corrosion0Reduced Engine Power from throttle body connector crimp, broken wire or grounds0P0420 / P0430 on a new or just-replaced catalytic converter (break-in not completed)0DTC P0446 set with the SES lamp on (replace the EVAP vent solenoid, not the canister)
8 causes not drawn
Causes with no correction stated (2)

Causes the records name for which no check or repair is stated, in a technical document or in a record. Press one for the records that name it.

Electrical, wiring and power
Intermittent no start with Service Stability, ABS light, 'Unknown Driver' and multiple DTCs / no module communication (0)
Brakes
Service Stability message with DTC C0131, C0196, C0290 and/or C0292 (0)

The documents say what to doOnly records name itThe size of a node, the width of a link and the numbers are records matching this search, not likelihoods.

FaultCrate・GMC Yukon 2000–2006・Warning light, Engine

Candidate cause (the documents say what to do)

Crankshaft position sensor may work intermittently or fail (8.1L V8) - recall 07V-521

Applies to: 8.1L only

The crankshaft position can operate intermittently or fail completely.

With intermittent operation the SES light may illuminate and the vehicle may run rough.

How to tell

Check engine / Service Engine Soon

What to do

  1. Dealers replace the crankshaft position sensor.
  2. As the remedy, an improved CKP is installed.
  3. The repair listed for the claim is: replace the crankshaft position sensor and perform the Crankshaft Position System Variation Learn.
  4. Part: 12575172 Sensor, Crankshaft Position, quantity 1 per vehicle.

Caution: All of the surveyed consumers noted multiple stalling events before the CKP was properly diagnosed and replaced.

What is needed

Parts and materials
  • Crankshaft position sensor 12575172 (quantity 1 per vehicle)

Part numbers printed in the document

The numbers are as the document prints them. The name and the replacing number are what the pages of GMPartsGiant, a reseller of genuine parts and not GM, state. Aftermarket equivalents are not checked here (the links only search by number). Confirm the fit for the vehicle (VIN) before ordering.

Labor time
Not stated
Special tools
Not stated
Scan tool
  • Crankshaft Position System Variation Learn

Only what the technical documents state. "Not stated" does not mean not needed.

In the records

No record states work done for this cause.

See the evidence (1 technical documents, 0 records)

Passages of the technical documents

  • The recall text refers to pickup trucks with an 8.1L V8 engine.

    ON CERTAIN PICKUP TRUCKS EQUIPPED WITH AN 8.1L V8 ENGINE,

    NHTSA 2007-11-07

  • The crankshaft position can operate intermittently or fail completely.

    THE CRANKSHAFT POSITION CAN OPERATE INTERMITTENTLY OR FAIL COMPLETELY.

    NHTSA 2007-11-07

  • With intermittent operation the SES light may illuminate and the vehicle may run rough.

    IF THE SENSOR OPERATES INTERMITTENTLY, THE SES LIGHT MAY ILLUMINATE AND THE VEHICLE MAY RUN ROUGH.

    NHTSA 2007-11-07

  • The engine may stall and may restart immediately or after a cool-down period.

    THE ENGINE MAY STALL, AND IF SO, MAY RE-START IMMEDIATELY OR AFTER A COOL DOWN PERIOD.

    NHTSA 2007-11-07

Read every statement and its source →

Records

None among the records that can be opened now.

See all 0 records of this cause →

A cause or a result a complaint states is the owner’s view or what a dealer told them, not an established fact.

Put together by FaultCrate from public records and technical documents. The cause and the repair are for the workshop to decide with the vehicle in front of it. Counts are records, not failure rates.