Skip to content
FaultCrate
日本語

This is an open preview: every record can be read without an account.

GMC Yukon XL 2000–2006

GMC Yukon XLModel years 2000–2006

Change vehicle →
Clear the search
2 conditions added

The vehicle (where a record says)

A record is under an engine, a drive or a series only where it says so: the characters of the vehicle identification number filed with a complaint, its text, or what its document says it applies to. A record that does not say is kept as "not stated". The filed numbers and the documents do not tell 4WD from AWD.

Common on this vehicle:LeakLoss of engine power, no accelerationWarning light

Record by record

2 records state a cause or a remedy. Each record is shown as short labels in the order fault → finding the cause → correction. Press a label to narrow to the records that state it.

Read the records one by one (2)

ELECTRONIC STABILITY CONTROL (ESC)1

  1. Owner complaint2003 GMC YUKON XL DENALI ・ 2012-12-18

    Power loss at 65 mph on highway, reduced engine power message, codes cleared but symptom persists

    1. 1Fault

    2. 2Finding the cause

      Not stated

    3. 3Correction

      Not stated

    Read the sentences of the record
    Fault
    DRIVING 65 MPH (= 104.6 km/h) ON THE HIGHWAY AND ALL OF A SUDDEN MY CAR LOSES POWER. (2 more)
    Outcome
    I GOT EVERYTHING DONE THAT WAS SUGGESTED THE CODES ARE GONE AND IT'S STILL HAPPENING!!

ENGINE AND ENGINE COOLING1

  1. Manufacturer communication2000–2006 GMC YUKON XL DENALI ・ 2022-09-07

    MIL Illuminated with Fuel Trim and Oxygen Sensor Codes

    1. 1Fault

      • Customers may comment that the MIL is illuminated.
      • Initial diagnosis may show fuel trim and O2 sensor related codes including P0101, P0137, P0138, P0140, P0141, P0157, P0158, P0160 and P0161.
      • The listed codes also include P0171, P0174, P0420, P0430, P1174 and P1175.

    2. 2Finding the cause

      Possible causes

      • These methods find small leaks around the O2 sensor embossments and slight cracks in an intake plenum or gasket.

      Steps to confirm (in the document’s order)

      1. If normal SI diagnostics do not lead to a resolution and an intake vacuum leak or exhaust leak is suspected, use the GE-52250 Variable Pressure Leak Detector (preferred), the J-41416 ultrasonic leak tester, or possibly soapy water with low pressure air into the tailpipe to find the leak.
      2. For an intake leak, introduce the smoke into the brake booster hose or the oil dipstick tube; soapy water can be sprayed near the gasket, seams and all vacuum nipples.
      3. For an exhaust leak, put the hose with smoke or air into the tailpipe sealed with shop towels, then spray soapy water around seals, seams and bosses.

    3. 3Correction

      Parts

      • No parts are required for this repair.

      Caution

      • All of these tests are much more effective if the throttle body is covered or sealed.
    Read the sentences of the record

    From the manufacturer’s document

    • Applies to：Applies to Buick, Cadillac, Chevrolet and GMC passenger cars and trucks, model years 2000 to 2022, gasoline engines only.
    • Condition：Customers may comment that the MIL is illuminated.
    • Condition：Initial diagnosis may show fuel trim and O2 sensor related codes including P0101, P0137, P0138, P0140, P0141, P0157, P0158, P0160 and P0161.
    • Condition：The listed codes also include P0171, P0174, P0420, P0430, P1174 and P1175.
    • Confirm：If normal SI diagnostics do not lead to a resolution and an intake vacuum leak or exhaust leak is suspected, use the GE-52250 Variable Pressure Leak Detector (preferred), the J-41416 ultrasonic leak tester, or possibly soapy water with low pressure air into the tailpipe to find the leak.
    • Caution：All of these tests are much more effective if the throttle body is covered or sealed.
    • Confirm：For an intake leak, introduce the smoke into the brake booster hose or the oil dipstick tube; soapy water can be sprayed near the gasket, seams and all vacuum nipples.
    • Confirm：For an exhaust leak, put the hose with smoke or air into the tailpipe sealed with shop towels, then spray soapy water around seals, seams and bosses.
    • Cause：These methods find small leaks around the O2 sensor embossments and slight cracks in an intake plenum or gasket.
    • Parts：No parts are required for this repair.

    Open the manufacturer’s document (PDF) ↗ The points above were read from this document.

    Remedy
    This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.